MacDon M Series - Page 12

TABLE OF CONTENT
S
3.21 Attaching Headers ......................................................................................................................... 97
3.21.1 Attaching Header Boots.......................................................................................................... 97
3.21.2 Attaching a D-Series Header ................................................................................................... 98
Attaching a D-Series Header: Hydraulic Center-Link with Optional Self-Alignment .............. 99
Attaching a D-Series Header: Hydraulic Center-Link without Self-Alignment...................... 104
Attaching a D-Series Header: Mechanical Center-Link.....................................................110
3.21.3 Attaching an A-Series Header................................................................................................114
Attaching an A-Series Header: Hydraulic Center-Link with Optional Self-Alignment............116
Attaching an A-Series Header: Hydraulic Center-Link without Self-Alignment ....................121
Attaching an A-Series Header: Mechanical Center-Link ................................................... 127
3.21.4 Attaching an R-Series Header................................................................................................132
Attaching an R-Series HeaderHydraulic Center-Link with Optional Self-Alignment..............133
Attaching an R-Series Header: Hydraulic Center-Link without Self-Alignment....................138
Attaching an R-Series Header: Mechanical Center-Link ................................................... 144
3.22 Lubricating the Windrower.............................................................................................................150
3.22.1 Lubrication Procedure ...........................................................................................................150
3.22.2 Lubrication Points..................................................................................................................151
4 Cab Display Module (CDM) ................................................................................................................. 153
4.1 Cab Display Module (CDM) Programming...................................................................................... 153
4.2 Cab Display Options.....................................................................................................................156
4.2.1 Setting the Cab Display Language..........................................................................................157
4.2.2 Changing the Windrower Display Units................................................................................... 160
4.2.3 Adjusting the Cab Display Buzzer Volume...............................................................................163
4.2.4 Adjusting the Cab Display Backlighting...................................................................................166
4.2.5 Adjusting the Cab Display Contrast ........................................................................................ 169
4.3 Calibrating the Header Sensors.....................................................................................................172
4.3.1 Calibrating the Header Height Sensor ..................................................................................... 172
4.3.2 Calibrating the Header Tilt Sensor.......................................................................................... 176
4.3.3 Calibrating the Header Float Sensors ..................................................................................... 180
4.4 Programming the Windrower......................................................................................................... 184
4.4.1 Selecting Header Type ..........................................................................................................184
4.4.2 Activating the Hydraulic Center-Link on an M105 and M155.....................................................185
4.4.3 Activating the Reel Fore-Aft Function on an M105...................................................................187
4.4.4 Activating the Rotary Header Drive Hydraulics on an M155...................................................... 188
4.4.5 Setting the Header Knife Speed ............................................................................................. 189
4.4.6 Setting the Knife Overload Speed........................................................................................... 190
4.4.7 Setting the Rotary Disc Overload Speed.................................................................................193
4.4.8 Setting the Hydraulic Overload Pressure................................................................................. 194
4.4.9 Setting the Header Index Mode..............................................................................................196
4.4.10 Setting the Return to Cut Mode.............................................................................................. 198
4.4.11 Setting the Header Cut Width .................................................................................................201
4.4.12 Activating the Double Windrow Attachment (DWA).................................................................. 204
4.4.13 Setting the Auto Raise Height ................................................................................................207
4.4.14 Activating the Hay Conditioner ...............................................................................................209
4.4.15 Displaying Reel Speed ..........................................................................................................211
4.4.16 Displaying the Speed of the Auger Header Reel...................................................................... 213
4.4.17 Setting the Windrower’s Tire Size........................................................................................... 215
4.4.18 Setting the Engine Intermediate Speed Control (ISC) RPM on an M105....................................217
4.4.19 Setting the Engine Intermediate Speed Control (ISC) RPM on an M155/M205 .......................... 218
4.4.20 Clearing Sub-Acres ...............................................................................................................221
4.5 Activating Cab Display Lockouts....................................................................................................222
4.5.1 Activating Knife Speed Control Lockout .................................................................................. 222
4.5.2 Activating Rotary Disc Speed Control Lockout......................................................................... 224
4.5.3 Activating the Header Float Control Lockout ............................................................................227
147962
x
Revision A