Anritsu ML2437A - Page 13

ML2437A/38A OM/PM PN: 10585-00001 Rev. P Contents-11
Table of Contents (Continued)
8-10 ML4803A Emulation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-85
SRQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-85
Status Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-85
Output Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-86
Unsupported Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-86
AVE (Sensor averaging setting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-87
CAL (Set the user cal factor value) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-87
CCA (Clear the calfactor value to zero). . . . . . . . . . . . . . . . . . . . . . . . 8-87
CDJ (Perform a CAL 0 dBm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-87
COF (Clear the offset value to zero) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-87
COS (Turn ON the 50 MHz, 0 dBm RF calibrator output) . . . . . . . . . . 8-87
CRF (Clear the reference value to zero) . . . . . . . . . . . . . . . . . . . . . . . 8-87
CST (Turn OFF the 50 MHz, 0 dBm RF calibrator output) . . . . . . . . . 8-87
DBM (Sets the display channel units to dBm) . . . . . . . . . . . . . . . . . . . 8-88
DBR (Sets display channel units to dB’s and takes the relative value) 8-88
EMUL (GPIB emulation mod) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-88
MCA (Set the cal factor value at the specified memory location in dBm)8-88
MCC (Clears the cal factor value at the specified memory location). . 8-89
MCO (Clears the offset value at the specified memory location) . . . . 8-89
MCQ (Clears the frequency value at the specified memory location) . 8-89
MCR (Clears the reference value at the specified memory location) . 8-89
MCT (Clears all the entries at the specified memory location) . . . . . . 8-89
MDI (Disable memory store setting and use) . . . . . . . . . . . . . . . . . . . 8-89
MEN (Enable setting of the memory stores) . . . . . . . . . . . . . . . . . . . . 8-89
MFG (Set the frequency value at the specified location in GHz). . . . . 8-90
MFM (Set the frequency value at the specified location in MHz) . . . . 8-90
MOF (Set the offset value at the specified location in dBm) . . . . . . . . 8-90
MRF (Set the reference value at the specified location in dBm) . . . . . 8-90
ODT (Output the current calibration factor, offset, and reference level)8-91
OFF (Set sensor offset value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-91
OI? (Request identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-91
OMR (Output a memory store set of data) . . . . . . . . . . . . . . . . . . . . . 8-92
OPW (Request for channel reading) . . . . . . . . . . . . . . . . . . . . . . . . . 8-92
REF (Set the reference value). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-95
RNG (Sensor measurement range hold). . . . . . . . . . . . . . . . . . . . . . . 8-95
SRQ (Turns on or off the SRQ on output data ready) . . . . . . . . . . . . . 8-95
STA (Restart averaging reading). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-95
WAT (Sets the display channel units to Watts) . . . . . . . . . . . . . . . . . . 8-95
ZAJ (Zero the sensor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-96