D-Link xStack DGS-3420 Series - Page 145

xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
140
udp - (Optional) Specifies that the following parameters configured will apply to the UDP
configuration.
src_port - Specifies the UDP source port range.
<value 0-65535> - Enter the UDP source port range value here.
mask - Specifies the UDP source port mask here.
<hex 0x0-0xffff> - Enter the UDP source port mask value here.
dst_port - Specifies the UDP destination port range.
<value 0-65535> - Enter the UDP destination port range value here.
mask - Specifies the UDP destination port mask here.
<hex 0x0-0xffff> - Enter the UDP destination port mask value here.
protocol_id - (Optional) Specifies that the rule will apply to the value of IP protocol ID traffic.
<value 0-255> - Enter the protocol ID used here. This value must be between 0 and 255.
user_define - (Optional) Specifies that the rule will apply to the IP protocol ID and that the mask
options behind the IP header, which has a length of 20 bytes.
<hex 0x0-0xffffffff> - Enter the user-defined mask value here.
mask - Specifies the user-defined mask here.
<hex 0x0-0xffffffff> - Enter the user-defined mask value here.
ipv6 - Specifies the rule applies to IPv6 fields.
class - (Optional) Specifies the value of IPv6 class.
<value 0-255> - Enter the IPv6 class value here. This value must be between 0 and 255.
source_ipv6 - (Optional) Specifies the value of IPv6 source address.
<ipv6addr> - Enter the source IPv6 source address here.
mask - Specifies the IPv6 source address mask here.
<ipv6mask> - Enter the IPv6 source address mask value here.
destination_ipv6 - (Optional) Specifies the value of IPv6 destination address.
<ipv6addr> - Enter the source IPv6 destination address here.
mask - Specifies the IPv6 destination address mask here.
<ipv6mask> - Enter the IPv6 destination address mask value here.
tcp - (Optional) Specifies the TCP protocol
src_port - Specifies the value of the IPv6 layer 4 TCP source port.
<value 0-65535> - Enter the IPv6 TCP source port value here. This value must be between
0 and 65535.
mask - Specifies the IPv6 TCP source port mask here.
<hex 0x0-0xffff> - Enter the IPv6 TCP source port mask value here.
dst_port - Specifies the value of the IPv6 layer 4 TCP destination port.
<value 0-65535> - Enter the IPv6 TCP destination port value here. This value must be
between 0 and 65535.
mask - Specifies the IPv6 TCP destination port mask here.
<hex 0x0-0xffff> - Enter the IPv6 TCP destination port mask value here.
udp - (Optional) Specifies the UDP protocol.
src_port - Specifies the value of the IPv6 layer 4 UDP source port.
<value 0-65535> - Enter the IPv6 UDP source port value here. This value must be between
0 and 65535.
mask - Specifies the IPv6 UDP source port mask here.
<hex 0x0-0xffff> - Enter the IPv6 UDP source port mask value here.
dst_port - Specifies the value of the IPv6 layer 4 UDP destination port.
<value 0-65535> - Enter the IPv6 UDP destination port value here. This value must be
between 0 and 65535.
mask - Specifies the IPv6 UDP destination port mask here.
<hex 0x0-0xffff> - Enter the IPv6 UDP destination port mask value here.
icmp - (Optional) Specifies that the following parameters configured will apply to the ICMP
configuration.
type - Specifies that the rule will apply to the ICMP type traffic value.
<value 0-255> - Enter the ICMP traffic type value here. This value must be between 0 and
255.