Hioki IM3536 - 5.1 Setting the Cable Length (Cable Length Correction)

276 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

92

Setting Application Settings

Table of Contents

Default Chapter3
- Table of Contents3
Introduction7
Verifying Package Contents7
Measurement Process12
Safety Information16
Operating Precautions18
1 Overview23
- Product Overview and Features23
- Names and Functions of Parts24
- Screen Layout and Operation26
2 Measurement Preparations37
- Preparation Flowchart37
- Pre-Operation Inspection39
- Connecting the Power Cord40
- Connecting the Measurement Cables, Probes, or Fixture41
- Turning the Power on and off42
- Setting the Date and Time44
3 Performing Measurements in LCR Mode45
- Setting Display Parameters45
  - X84; to Perform DC Measurement (DC Resistance Measurement)46
- Viewing Measured Values47
- Enlarging Display of Measurement Values48
- Setting Measurement Conditions (Basic Settings)49
- Judging Measurement Results74
- Setting Application Settings85
4 Using Continuous Measurement Mode99
- Setting Which Panels to Use in Continuous Measurement99
- Performing Continuous Measurement100
- Checking Continuous Measurement Results100
- Changing the Display Timing Setting (When You Wish to Shorten the Screen Update Interval)101
- Setting the LCD Display Auto-Off (When You Wish to Save the Power)102
5 Error Correction103
- Setting the Cable Length (Cable Length Correction)104
- Open Correction105
- Short Correction111
- If Open or Short Correction Fails to Complete Normally115
- Disabling Open and Short Correction Values117
- Load Correction (Correcting Values to Match Reference Values)118
- Correcting Measured Values with a User-Specified Correction Coefficient (Correlation Correction)127
6 Saving and Loading Measurement Condition and Correction Value Data129
- Saving Measurement Conditions and Correction Values (Panel Save Function)130
- Loading Measurement Conditions and Correction Values (Panel Load Function)134
- Changing a Panel Name135
- Deleting a Panel136
7 Setting the System137
- Setting the Interface (Controlling the Instrument from a Computer)138
- Checking the Version of the Instrument138
- Testing the System (Self Diagnosis)139
8 Using USB Flash Drive (Saving and Loading Data)143
- Inserting and Removing a USB Flash Drive144
- Checking the Contents of Files on a USB Flash Drive145
- Formatting a USB Flash Drive146
- Saving Measurement Data147
- Saving Settings Data159
  - X84; Saving Instrument Settings Other than Panels159
  - Panels (ALL SAVE Function)160
- Loading Instrument Settings161
  - X84; Loading Settings Files or Panel Files161
  - Files (ALL LOAD Function)162
- Checking the Contents of a File163
- Deleting Files and Folders164
- Creating Folders165
- Displaying the USB Flash Drive Information166
9 External Control167
- External Input/Output Connector and Signals168
- Example Measurement Timing (Timing Charts)177
- Internal Circuitry182
- External I/O Settings186
- External Control Q&A191
- Result Output to EOM Output) and Judgment Result Reset Operation191
- Measurement Using a Computer192
10 Specifications193
- General Specifications193
- Environmental and Safety Specifications198
- Accessories and Options199
- Function Specifications199
- Interfaces211
- Measurement Range and Accuracy213
- About Measurement Times and Measurement Speed223
11 Maintenance and Service227
- Calibration, Inspection, Repair, and Cleaning227
- Troubleshooting229
- Error Massage and Error Display236
- Discarding the Instrument241
  - Formula243
Appendix Appx243
- Appx. 3 Measurement of In-Cir Cuit Components246
- External Noise247
- X84; Countermeasures against Incorporation of Noise from the Power Line247
- X84; Countermeasures against Noise from the Measurement Cables248
Appx. 5 Supplying DC Bias248
- X84; How to Supply a DC Bias Voltage249
- X84; How to Supply a DC Bias Current250
- Appx. 6 the Residual Charge Protection Function251
Appx. 7 Series Equivalent Circuit Mode and Parallel Equivalent252
- Short Correction253
  - Appx. 8 Open Correction and Short Correction253
  - Hardware to the Instrument Appx254
- Appx.12255
Appx. 10 Dimensional Diagram256
Appx. 11 Initial Settings Table257
- Appx. 12 Device Compliance Statement264

Related product manuals

Preview: Hioki IM3533

Preview: Hioki IM3533-01

Hioki IM3533-01

Preview: Hioki IM3523

Preview: Hioki IM3570

Hioki IM7580A Series

Preview: Hioki 3332

Preview: Hioki 3151

Preview: Hioki CM4001

Preview: Hioki PW3198

Preview: Hioki 3283-20

Preview: Hioki BT3562-01

Hioki BT3562-01