Honeywell DR4500A User Manual

Honeywell Field Solutions
DR4500A Classic Series Circular Chart
Recorder With or Without Control
Product Manual
Doc. No.: 44-45-25-35
Release: M
Last Revision Date: April 2017

Honeywell DR4500A Specifications

General

Model	DR4500A
Power Supply	100-240 VAC, 50/60 Hz
Operating Temperature	0 to 50°C (32 to 122°F)
Input Type	Thermocouple, RTD, mV, V, mA
Chart Size	10 inch (254 mm)

Summary

2. Installation

2.2 Model Number Interpretation

2.5 Wiring Prerequisites

Outlines precautions and requirements for electrical wiring and grounding.

2.6 Input Wiring Procedures

Provides instructions for wiring the recorder's inputs based on model number.

2.7 Output Wiring Procedures

Provides instructions for wiring the recorder's outputs.

2.9 Lockout Switch Configuration

3. Configuration

3.3 How To Get Started

3.5 Configuration Procedure

3.6 Input Set Up Group

Parameters for configuring recorder inputs 1 and 2.

3.7 Pen Set Up Group

3.8 Chart Set Up Group

3.10 Control Set Up Group

Parameters for controlling the process and recorder functions.

3.11 Tuning Parameters Set Up Group

Parameters for adjusting tuning constants for optimal response.

3.12 SP Ramp Set Up Groups

3.14 Alarms Set Up Group

Parameters for configuring the recorder's alarm functions.

3.16 Modbus Communications Set Up Group

3.18 Lockout Set Up Group

Parameters to prevent unauthorized changes to configuration and calibration.

4. Configuration Parameter Definitions

4.2 Input Parameters Set Up Group

Definitions for parameters related to recorder inputs 1 and 2.

4.3 Pen Parameters Set Up Group

4.4 Chart Parameters Set Up Group

4.6 Control Parameters Set Up Group

Definitions for parameters controlling process and recorder functions.

4.7 Tuning Parameters Set Up Group

Definitions for parameters adjusting tuning constants for optimal response.

4.8 Setpoint Ramp Set Up Group

4.10 Alarms Set Up Group

Definitions for parameters related to alarm functions.

4.12 Modbus Communications Set Up Group

4.14 Lockout Parameters Set Up Group

Definitions for parameters to prevent unauthorized changes.

5. Operation

5.3 Start-up

5.4 Monitoring Your Recorder

How to monitor recorder indicators, displays, and error messages.

5.5 Operator Functions

Actions an operator can initiate on the recorder.

5.6 Operating Modes

5.7 Setpoints

Procedures for configuring and changing setpoints.

5.8 Single Setpoint Ramp

5.9 Using Two Sets of Tuning Constants (PID Values)

Procedure for using and switching between two sets of PID tuning constants.

5.10 Using Accutune II

5.11 Alarm Setpoints

Procedure for displaying and changing alarm setpoints.

6. Setpoint Ramp/Soak Programming and Operation

Setpoint Program Contents

Drawing a Ramp/Soak Profile

Entering the Setpoint Program Data

Procedure for entering setpoint program data using the keypad.

SP RAMP1 and SP RAMP2 Set Up Group

Prompts for configuring setpoint ramps for control loops 1 and 2.

Setpoint Program Profiles Set Up Group

Setpoint Program Segments Set Up Group

Setpoint Program Event Set Up Group

Run/Monitor the Program

Instructions for running, monitoring, holding, and ending setpoint programs.

7. Input Calibration

7.2 Restoring Factory Calibration

Calibration Set Up and Wiring for PV Inputs

Details jumper positions and wiring for PV input calibration.

Calibration Procedure

Step-by-step procedure for calibrating all input types.

8. Output Calibration

Current Proportional Output/Aux Out 2 and 3 Calibration

Procedure for calibrating current proportional and auxiliary outputs.

Position Proportional Output Calibration

Procedure for calibrating position proportional output control.

Auxiliary Output Calibration

Procedure for calibrating the auxiliary output.

9. Troubleshooting / Service

Troubleshooting Aids

Self Diagnostics

Details power-up tests and error messages for system diagnostics.