Index
Keysight InfiniiVision DSOX1204A/G Oscilloscopes Programmer's Guide 937
CSV (Comma Separated Values) waveform
data format, 455
current oscilloscope configuration, 117,
120, 124, 567
current probe, 220, 258
CURRent segment waveform save
option, 458
cursor mode, 328
cursor position, 329, 331, 333, 336, 338
cursor readout, 733, 737, 738
cursor reset conditions, 121, 556
cursor source, 330, 332
cursor time, 733, 737, 738
cursor units, X, 334, 335
cursor units, Y, 339, 340
cursors track measurements, 379
cursors, how autoscale affects, 137
cursors, X1, X2, Y1, Y2, 326
cycle measured, 361, 364
cycle time, 371
D
data, 486, 488, 642
data (waveform) maximum length, 457
data 2, 489
data acquisition types, 635
data conversion, 637
data format for transfer, 638
data output order, 640
data pattern length, 480, 505
data pattern, CAN trigger, 479
data point index, 664
data points, 182
data record, measurement, 647
data record, raw acquisition, 647
data required to fill time buckets, 179
data source, setup and hold trigger, 619
data structures, status reporting, 767
data, saving and recalling, 228
date, calibration, 193
date, system, 548
dB versus frequency, 291
DC coupling for edge trigger, 598
DC input coupling for specified
channel, 206
DC RMS measured on waveform, 392
DC waveform generator output, 674
DDE (Device Dependent Error) status
bit, 113, 115
decision chart, status reporting, 785
default conditions, 121, 556
define channel labels, 210
define glitch trigger, 608
define measurement, 357
define measurement source, 380
define trigger, 609
defined as, 103
definite-length block query response, 46
definite-length block response data, 104
delay measured to calculate phase, 372
delay measurement, 357
delay measurements, 382
delay parameters for measurement, 359
delay, how autoscale affects, 137
delayed time base, 575
delayed window horizontal scale, 583
delete mask, 415
delta time, 733
delta voltage measurement,
741
delta X cursor, 326
delta Y cursor, 326
demo, 223
DEMO commands, 223
demo signal, 224
demo signal function, 224
demo signals output control, 226
destination, remote command logging, 561
detecting probe types, 719, 722
device-defined error queue clear, 111
differences from 1000 X-Series oscilloscope
commands, 28
differential probe heads, 213
differential signal type, 216
digital channel source for glitch
trigger, 610
digitize channels, 143
DIGitize command, 38, 43, 636
digits, 104
disable front panel, 552
disable function, 725
disabling calibration, 196
disabling channel display, 207
disabling status register bits, 112, 125
discontinued and obsolete commands, 711
display annotation, 229
display annotation background, 230
display annotation color, 231
display annotation text, 232
display channel labels, 236
display clear, 233
DISPlay commands, 227
display commands introduction, 228
display connect, 720
display date, 548
display factors scaling, 212
display for channels, 207
display frequency span, 268, 295
display measurements, 350, 379
display persistence, 239
display reference, 576, 578
display reference waveforms, 704
display reset conditions, 122
, 557
display serial number, 160
display vectors, 240
display, FFT function, 262
display, oscilloscope, 239, 292, 550
display, serial decode bus, 464
displaying a baseline, 596
displaying unsynchronized signal, 596
divide math function, 303
DNS IP, 34
domain, 34
driver, printer, 730
duplicate mnemonics, 803
duration for glitch trigger, 604, 605, 609
duration triggering, 586
duty cycle measurement, 39, 350, 361,
364
DVM commands, 241
DVM displayed value, 243
DVM enable/disable, 244
DVM frequency value, 245
DVM input source, 247
DVM mode, 246
E
edge coupling, 598
edge fall time, 362
edge parameter for delay
measurement, 359
edge preshoot measured, 374
edge rise time, 377
edge slope, 601
edge source, 602
EDGE trigger commands, 597
edge triggering, 585
edges in measurement, 357
eject USB storage devices, 570
elapsed time in mask test, 412
ellipsis, 104
enable channel labels, 236
enabling calibration, 196
enabling channel display, 207
enabling status register bits, 112, 125
end of string (EOS) terminator, 800
end of text (EOT) terminator, 800
end or identify (EOI), 800
EOI (end or identify), 800
EOS (end of string) terminator, 800
EOT (end of text) terminator, 800
erase data, 233
erase measurements, 732
erase screen, 721
error frame count (CAN), 468
error frame count (UART), 528
error messages, 551, 757
error number, 551
error queue, 551, 778
error, measurement, 350
ESB (Event Status Bit), 126, 128
ESE (Standard Event Status Enable
Register), 112, 777
ESR (Standard Event Status Register), 114,
776
event status conditions occurred, 128
Event Status Enable Register (ESE), 112,
777
Event Status Register (ESR), 114, 164, 776
example code, :ACQuire:COMPlete, 179
example code, :ACQuire:SEGMented, 185
example code, :ACQuire:TYPE, 190
example code, :AUToscale, 138
To Next Page
Loading...
Need help?
General
