Parker AC30 series - Page 444

C-262 Parameter Reference
AC30 series Variable Speed Drive
1794
Soft Key 2 Mode
Parameters::Keypad::Graphical Keypad
USINT
(enum)
0
0:LOCAL / REMOTE
1:FORWARD / REVERSE
2:CUSTOM
ALWAYS
OPERATOR
04115
1795
Soft Key 2 Value
Parameters::Keypad::Graphical Keypad
BOOL
FALSE
ALWAYS
OPERATOR
2
04117
1796
Alignment On Power On
Setup::Motor Control::Pos Fbk Alignment
Parameters::Motor Control::Pos Fbk Alignment
BOOL
FALSE
STOPPED
TECHNICIAN
6,4
04119
1797
Alignment Method
Same as PNO 1796
USINT
(enum)
0
0:MANUAL
1:AUTOMATIC
2:DIRECTION TEST
STOPPED
TECHNICIAN
6,4
04121
1798
Alignment Enable
Same as PNO 1796
BOOL
FALSE
STOPPED
TECHNICIAN
2,4
04123
1799
Alignment Level
Same as PNO 1796
REAL
50
0 to 150
%
ALWAYS
TECHNICIAN
6,4
04125
1800
Alignment Ramp Time
Same as PNO 1796
TIME
1.000
0.000 to 30.000
s
ALWAYS
TECHNICIAN
6,4
04127
1801
Alignment On Motor
Same as PNO 1796
USINT
(enum)
0
0:PHASE U
1:PHASE V
2:PHASE W
ALWAYS
TECHNICIAN
6,4
04129
1802
Alignment Offset
Parameters::Motor Control::Pos Fbk Alignment
REAL
x.x
-180.0 to 180.0
deg
NEVER
TECHNICIAN
4
04131
1803
Alignment Elec Pos
Parameters::Motor Control::Pos Fbk Alignment
REAL
x.x
-180.0 to 180.0
deg
NEVER
TECHNICIAN
4
04133
1804
Alignment Direction
Parameters::Motor Control::Pos Fbk Alignment
USINT
(enum)
0:STANDARD
1:REVERSE
NEVER
TECHNICIAN
4
04135
1805
Alignment State
Parameters::Motor Control::Pos Fbk Alignment
USINT
(enum)
0:OFF
1:ON MANUAL
2:ON AUTO
3:ERROR
4:ENDED
NEVER
TECHNICIAN
4
04137
1806
Alignment Ended
Parameters::Motor Control::Pos Fbk Alignment
BOOL
NEVER
TECHNICIAN
4
04139
1807
Alignment Error
Parameters::Motor Control::Pos Fbk Alignment
USINT
(enum)
0:NO ERROR
1:SHAFT LOCKED
2:AMPS
3:LOAD
4:POLES
5:MOTOR UNCONNECTED
6:ENCODER
7:INIT NEEDED
NEVER
TECHNICIAN
4
04141
1808
PMAC Encoder Offset
Setup::Motor Control::Motor Data PMAC
Parameters::Motor Control::PMAC Motor Data
REAL
0.0
-180.0 to 180.0
deg
ALWAYS
TECHNICIAN
1,6,9,4
04143
1809
PMAC Wiring
Setup::Motor Control::Motor Data PMAC
Monitor::Motor and Drive
Parameters::Motor Control::PMAC Motor Data
USINT
(enum)
0
Same as PNO 1804
ALWAYS
TECHNICIAN
6,9,4
04145
1810
Resolver Invert
Same as PNO 1790
BOOL
FALSE
STOPPED
TECHNICIAN
4
04147
1811
Resolver Turns
Monitor::Inputs and Outputs
Parameters::Option IO::Resolver
DINT
Min to Max
NEVER
TECHNICIAN
1,4
04149
1812
Resolver Fraction Turns
Same as PNO 1811
DINT
Min to Max
NEVER
TECHNICIAN
1,4
04151
1813
Resolver Speed RPM
Parameters::Option IO::Resolver
REAL
x.x
Min to Max
RPM
NEVER
TECHNICIAN
4
04153
1814
Resolver Speed %
Same as PNO 1811
REAL
x.x
Min to Max
%
NEVER
TECHNICIAN
4
04155
1815
Resolver Speed Filter
Same as PNO 1790
REAL
1000
10 to 10000
%
ALWAYS
TECHNICIAN
4
04157
1816
Resolver Resolution
Same as PNO 1790
USINT
(enum)
0
0:AUTO
1:12 BITS
2:14 BITS
3:16 BITS
STOPPED
TECHNICIAN
4
04159
1817
Resolver State
Parameters::Option IO::Resolver
USINT
(enum)
0:POWER_ON
1:RESET
2:ACTIVE
3:TRIPPED
4:RESTART
NEVER
TECHNICIAN
4
04161
1818
Resolver Turns Reset
Parameters::Option IO::Resolver
BOOL
FALSE
ALWAYS
TECHNICIAN
2,4
04163
1819
Resolver Reset Power On
Parameters::Option IO::Resolver
BOOL
FALSE
STOPPED
TECHNICIAN
4
04165
1820
Resolver Trip Type
Parameters::Option IO::Resolver
USINT
(enum)
0:NONE
1:PARITY
2:PHASE ERROR
3:MAX VELOCITY
4:TRACKING ERROR
5:SIN COS MISMATCH
6:SIN COS OVERRANGE
7:SIN COS BELOW LOS
8:SIN COS CLIPPED
NEVER
TECHNICIAN
4
04167
1821
Resolver Speed Hz
Parameters::Option IO::Resolver
REAL
x.x
Min to Max
Hz
NEVER
TECHNICIAN
4
04169
1822
Resolver Built-In Gear
Same as PNO 1790
REAL
1.0
0.1 to 1000.0
STOPPED
TECHNICIAN
4
04171
1823
Resolver Speed Ripple
Parameters::Option IO::Resolver
REAL
x.xx
0.00 to 1000.00
%
NEVER
TECHNICIAN
4
04173
1824
Resolver Position
Same as PNO 1811
INT
-32768 to 32767
NEVER
ENGINEER
1,4
04175