Siemens SIMOCODE pro System Manual

SIMOCODE pro
Index-8 GWA 4NEB 631 6050-22 DS 03
Index
Molded case circuit breaker (MCCB) 3LV
E-10
Monitoring 0/4 - 20 mA 1-126, Glossary-9
Monitoring for further availability 1-16
Monitoring for undervoltage 1-16
Monitoring functions 1-15, 5-1,
Glossary-9
Monitoring interval for mandatory
testing 5-1, 5-24
Monitoring interval for testing 1-127
Monitoring of current limits I< 5-7
Monitoring of current limits I> 5-6
Monitoring the number of starts 5-20,
Glossary-9
Monitoring voltage Glossary-9
Motor control 1-4, 4-1
Motor control functions 1-29
Motor current monitoring 5-5
Motor feeder 1-9, 2-3
Motor model 10-17
Motor operating hours 1-22, 1-67
Motor operating hours > 15-5
Motor protection 3-1, Glossary-10
Motor protection and motor control
status 1-63
Motor protection functions 3-2
Motor stop time 1-16, 1-68
Motor stop time > 1-68, 15-5
Motor stop time monitoring 5-19,
Glossary-10
Motor stop times 1-22, 5-18, 5-19
Motor switching state 1-22
Motor temperature 1-15
Molded Case Circuit Breaker (MCCB)
control function 4-27
Mounting 13-1
Mounting basic units D-4
Mounting lugs 13-3, 13-4, 13-6, 13-7
Mounting lugs for screw attachment 13-3
Mounting position D-2
Mounting the basic units, expansion mo-
dules and the decoupling module 13-4
Mounting, analog module D-19
Mounting, current measuring modules,
current/voltage measuring modules
13-6, 13-7, D-7
Mounting, decoupling module D-9
Mounting, digital modules D-10
Mounting, DM-F module D-12
Mounting, earth-fault module D-20
Mounting, operator panel D-22
Mounting, operator panel with display
D-23
Mounting, temperature module D-21
N
Navigating the menu of the operator panel
with display 1-40
Navigation in SIMOCODE ES 11-1, 12-1
Network contactor 4-33
No start 1-
68
No start possible 15-5
Non-maintained command mode 1-64,
4-16, 4-23, 4-26, 4-29, 4-32, 4-36, 4-39,
4-43, 4-46, 4-50, 4-53, 4-57, 4-60, 4-64
Non-safety functions (failsafe digital
modules) 7-11
Non-volatile element 1 (2, 3, 4) 1-122
Non-volatile element logic modules 11- 18
Non-volatile element settings 11-20
Non-volatile elements 1-21, 11-2, 11-18,
11-19, 11-20
NOR function 11-17, 11-20
Notes on parameterizing 14-3
NTC 1-80
Number of motor starts 1-22
Number of overload trips 1-22, 1-67
Number of parameterizations 1-69
Number of permissible starts
remaining 1-22
Number of starts 1-16, 5-20
Number of starts - actual value 1-67
Number of starts - overshoot 5-19
Number of starts - pre-warning 5-19
O
Object Manager OM SIMOCODE pro
1-110
OFF command-reset 10-11
OM SIMOCODE pro 12-2
ON control command 4-53
ON, ON>>, Start active 1-63
Operator Panel 4-9
OP Buttons 1-116, 7-8
OP LED 1-115
Open circuit, analog module 1-79
Operating data 1-5, 1-22
Operating hours 1-16, 5-18
Operating hours BU 1-69
Operating hours monitoring 5-19,
Glossary-10
Operating manual failsafe digital module
DM-F Local 1-18, 1-102
Operating manual failsafe digital module
DM-F PROFIsafe 1-18, 1-102
Operating modes 4-1, 4-5, 4-6
Operating modes for calculator 2 11-28
Operating range, basic units D-4
Operating range, DM-F D-12
Operating, service and diagnostic data
1-22

Siemens SIMOCODE pro Specifications

General

Protection Class	IP20
Mounting Type	DIN rail mounting
Rated Operational Voltage	24 V DC
Rated Current	Up to 820 A
Protection Functions	Overload, short-circuit, phase failure, asymmetry, ground fault, motor stall
Operating Temperature Range	-25°C to +60°C
Communication Protocols	PROFIBUS DP, PROFINET, Modbus RTU
Analog Outputs	Up to 2
Temperature Monitoring	PTC/KTY, RTD (PT100/PT1000)
Digital Outputs	Relay outputs, Solid-state outputs
Analog Inputs	0/4-20mA, PT100/PT1000