Siemens SIMOCODE pro

SIMOCODE pro
GWA 4NEB 631 6050-22 DS 03
Index-9
Index
Operation as DPV1 slave downstream
from the Y link 1-20
Operation monitoring 1-116, 5-1, 5-18,
Glossary-10
Operational Protection OFF 1-20, 10-2,
10-12, 10-13, 15-5, Glossary-10
Operational Protection OFF (OPO) function
block 10-12
Operator controls of the operator panel
with display 1-39
Operator panel 1-24, 1-32, 13-2, 14-2,
F-9, 7-7, Glossary-10
Operator panel adapter 1-27, 1-108, 13-2,
14-2, C-16, F-9
Operator panel buttons 7-1, 7-3, 7-6
Operator panel LEDs 6-1, 6-6
Operator panel with display 1-7, 1-24, 1-
1-34, 13-2, 14-2, F-9
Operator panel, "Test/Reset" button 7-6
Operator panel, buttons 1 to 4 7-6
OPO 1-117, 10-12
OPO, Remote, TPF 1-64
Organization blocks Glossary-11
Output of an analog value 6-15
Output of the effective motor current
6-13, 6-14
Output response of the timer 11-12, 11-13
Output, analog module 1-79, D-19
Outputs 1-75, 6-1, 6-3
Outputs 1,2 "monostable" 1-77
Outputs 1,2, feedback circuit DM-F
Local 1-78
Outputs 1,2, feedback circuit
DM-F PROFIsafe 1-78
Outputs DM-F Local 1-78
Outputs DM-F PROFIsafe 1-78
Overload 3-10, 15-5
Overload operation 15-5
Overload protection 1-13, 1-15, 3-1, 3-2,
3-5, 3-14, Glossary-11
Overload relay 1-13, 1-19, 1-30, 4-14, 4-
4-20, B-45, E-4, E-5
Overload relay control function 4-20
Overtemperature 5-23, 5-24
P
Panel reset 10-11
Parameter 4-16, 15-6
Parameter changes not allowed in the cur-
rent operating state 15-6
Parameter incorrect 15-6
Parameterization 2-6
Parameterization during startup 12-17
Parameterization via PROFIBUS 12-25
Parameterization with SIMOCODE ES
2-8
Password 15-10
Pause time 3-10, Glossary-11
Pause time active 1-65
PC cable 1-27, 1-107, 13-36, 13-42,
Glossary-11
PCS 7 SIMOCODE pro function block
librar
y 1-28
Performance Level (PL) 1-18, 1-10
1,
Glossary-11
Permissible ambient temperature D-2
Permissible number of starts
exceeded 15-6
Permissible starts 5-20
Permissible starts - actual value 1-68
PFD Abbreviations-2
PFDavg (IEC 61508) F-8
PFHD Abbreviations-2
Phase failure monitoring 1-13
Phase sequence 1-22, 1-94
Phase sequence 1-2-3 1-65
Phase sequence 3-2-1 1-65
Phase sequence identification 1-17
Phase unbalance 1-22, 1-60, 3-13, 15-6
Pin assignment of the removable
terminals 13-18, 13-20, 13-22, 13-24,
13-27, 13-32
Pin assignment of the removable terminals
of the basic unit 13-14
Pin assignment of the removable terminals
of the digital module 13-16
Pin assignment of the removable terminals
of the digital module DM-F Local 13-26
Pin assignments for digital module
DM-F PROFIsafe, 24 V DC version
13-27
Plant downtimes 5-18
Plant identifier 1-89
PLC/PCS 4-5, 4-9
PLC/PCS in Run 1-73
PLC/PCS monitoring 1-20, 1-73, 10-2,
10-24, 10-25
Plugs (analog) 1-111
Plugs (binary) 1-111
Pole-changing reversing starter 4-14,
4-50, B-54, E-26, E-27, E-28
Pole-changing reversing starter control
function 4-47
Pole-changing starter 1-13, 1-19, 1-30,
4-14, 4-46, B-53, E-24, E-25
Pole changing starter control function
4-44
Positioner 1-13, 1-19, 4-14, 4-57, 10-12,
10-13, B-56, E-32, E-33, E-34, E-35, E-36,
E-37, E-38, E-39, E-40, E-41
Positioner closes 1-64
Positioner control 1-30, 4-56