Siemens SIMOCODE pro System Manual

SIMOCODE pro
Index-10 GWA 4NEB 631 6050-22 DS 03
Index
Positioner control function 4-54, 10-12
Positioner opens 1-64
Power considerations 1-13
Power consumption, basic units D-4
Power consumption, DM-F D-12
Power factor 1-22
Power failure (UVO) 15-6
Power failure monitoring 1-20, 10-2,
10-15, 10-16
Power failure monitoring settings 10-16
Power failure time 10-16
Power loss ride-through time, DM-F D-12
Power management 1-13
Power monitoring 1-13, 1-127
Power-up behavior 3-5
Pre-alarm delay 3-12
Preparing the data transfer 12-17
Prerequisites for commissioning and
servicing 14-2
Preventive maintenance 14-8
Pre-warning level 3-12
Pre-warning overload (I >115%) 15-6
Process alarms 12-7
Process and diagnostic alarm 12-17
Process automation Glossary-11
Process monitoring 1-15
Product Information System (ProdIS) ii-
xiii, F-10, Abbreviations-2
PROFIBUS Glossary-12
PROFIBUS address 1-72
PROFIBUS communication (OPD) 1-45
PROFIBUS DP 1-20, 1-28, 2-2, 4-4, 4-59,
4-62, 6-2, 6-3, 6-5, 6-16, 6-18, 7-17, 10-7,
12-2, Glossary-12
PROFIBUS DP interface 1-20,
Glossary-12
PROFIBUS DP interface, basic units D-4
PROFIBUS DP to a 9-pole SUB-D socket
13-46
PROFIBUS DPV1 6-18, 7-17, 12-2,
Glossary-12
PROFIBUS User Organization (PUO) in-
stallation guidelines 13-47, Glossary-12
PROFINET Glossary-12
PROFIsafe 12-3, Glossary-12
PROFIsafe address 1-72
Programmable logic controller (PLC)
Glossary-13
Programming device Glossary-13
Protection functions 1-15
Protection/Control 1-122
Protective extra low voltage (PELV)
Glossary-13
Pt100 1-80
Pt1000 1-80
PTC 3-15
PTC high resistance/not present 1-75
PTC ok
1-75
PTC short
circuit 1-75
Pump 1-11, 1-15
R
Rated control supp
ly voltage Us D-4
Rated control supply voltage Us,
DM-F D-12
Rated impulse withstand voltage Uimp,
basic units D-4
Rated impulse withstand voltage Uimp,
DM-F D-12
Rated insulation voltage Ui, basic units
D-4
Rated insulation voltage Ui, DM-F D-12
Rated motor current F-4
Reaction times, typical D-27
Read and adapt main display 1-54
Reading data 12-3
Reading out statistical data 14-8
Reading out the device-internal error
buffer 1-87
Reading out the device-internal event
memory 1-88
Receive data from PROFIBUS DP 1-111,
7-1
Relay enabling circuits, DM-F D-12
Relay outputs 6-1
Relay outputs, basic units D-5
Relay outputs, digital modules D-10
Relay outputs, DM-F D-12
Relay test 10-6, F-7
Releases 4-1, 4-7
Remote operation 4-5
Remote reset 10-11
Remote/Automatic 4-5, 4-6
Removable terminals 13-3, 14-13
Repairs F- 9
Replacing a basic unit 14-11
Replacing a DM-F 14-12
Replacing an expansion module or a
decoupling module 14-12
Required function is not supported 15-7
Reset 1-20, 3-12, 10-2
Reset 1 (2, 3) 1-125
Reset display settings 1-84
Reset function 10-4, 10-5
Reset settings 10-7
Resetting, testing and parameterizing via
commands 1-85
Resistive load 4-17
Response xii, 3-4, 3-14
Restart 1-85
Restart temperature F-5
Restart time delay 10-15

Siemens SIMOCODE pro Specifications

General

Protection Class	IP20
Mounting Type	DIN rail mounting
Rated Operational Voltage	24 V DC
Rated Current	Up to 820 A
Protection Functions	Overload, short-circuit, phase failure, asymmetry, ground fault, motor stall
Operating Temperature Range	-25°C to +60°C
Communication Protocols	PROFIBUS DP, PROFINET, Modbus RTU
Analog Outputs	Up to 2
Temperature Monitoring	PTC/KTY, RTD (PT100/PT1000)
Digital Outputs	Relay outputs, Solid-state outputs
Analog Inputs	0/4-20mA, PT100/PT1000