SIMOCODE pro
GWA 4NEB 631 6050-22 DS 03
Index-11
Index
Restart time delay (staggered) 10-16
Return to main display 1-84
Reversing starter 1-13, 1-19, 1-30, 2-1,
2-2, 2-7, 2-9, 4-14, 4-26, B-47, E-8, E-9
Reversing starter control function 4-24
Routing function 12-20, 12-25
S
S7 slave via OM SIMOCODE pro 12-17
Safe isolation according to
IEC 60947-1 D-3
Safe isolation according to IEC 60947-1,
DM-F D-12
Safe Tripping 10-3
Safe Tripping reset 10-23
Safe Tripping response 10-23
Safe Tripping, DM-F Local 1-123
Safe Tripping, DM-F PROFIsafe 1-123
Safety and commissioning information for
EEx areas F-1
Safety data F-8
Safety DM-F Local 1-66
Safety DM-F PROFIsafe 1-66
Safety extra low voltage Glossary-13
Safety guidelines F- 8
Safety Integrity Level 1-18, 1-101,
Glossary-14
Safety/PROFIsafe - separate function from
control function 4-17
Safety-oriented tripping 1-14, 1-18, 10-18
Safety-oriented tripping "Local" 1-20
Safety-oriented tripping "PROFIsafe" 1-20
Safety-oriented tripping monitoring 1-22
Saving change-over command 4-16, 4-26,
4-36, 4-39, 4-43, 4-46, 4-50, 4-64
Saving parameters from a SIMOCODE ES
file into the basic unit 14-10
Saving parameters from the basic unit into
a SIMOCODE ES file 14-9
Saving parameters from the basic unit into
the memory module 14-9
Saving parameters from the memory mo-
dule into the basic unit 14-10
Schematic of the "OP Buttons" function
block 7-8
Screw attachment 13-3, 13-4, 13-6, 13-7
Screw terminals 1-111, 1-112
SELV Glossary-13
Send data on the PROFIBUS DP 6-1
Sensor channels 1,2, DM-F Local 1-78
Sensor channels DM-F Local 1-78
Sensor circuit fault 3-16
Sensor circuit wiring F-6
Sensor circuit, temperature module D-21
Sensor fault 1-80, 3-16
Sensor input automatic start/monitored
start 10-21
Sensor measuring circuit 1-16, 1-22
Sensor out of range
1-80
Se
nsor type 1-80
Sensor types 1-105
Senso
rs 1-26
Separate failsafe function from control
function 4-20, 4-23, 4-26, 4-29, 4-32,
4-36, 4-39, 4-43, 4-46, 4-50, 4-53, 4-57,
4-60, 4-64
Sequence for connecting cables to the sys-
tem interface 13-40
Sequence for connecting cables to the sys-
tem interface of the operator panel
13-43
Sequence for connecting PROFIBUS DP to
the basic unit 13-46
Service 14-1
Service and support xiii, F-10
Service data 1-5, 1-22
Set current 3-5
Set current Is2 3-6
SET/RESET button, DM-F Local 10-19, D-
D-16
SET-RESET button, DM-F PROFIsafe
D-17
Setting the PROFIBUS DP address 2-10
Setting the PROFIBUS DP address via
SIMOCODE ES 2-11, 14-5
Setting the PROFIBUS DP address via the
addressing plug 2-11, 14-5
Setting the PROFIsafe address on
DM-F PROFIsafe 14-5
Setting the rated motor current F-4
Setting up in hazardous areas F- 8
Settings of the DIP switches
(DM-F Local) 10-19, 10-20
Settings of the DIP switches
(DM-F PROFIsafe) 10-22
Set-up F- 3
SFB Glossary-13
SFC Glossary-13
Shock resistance (sine pulse) D-2
Short code 1-90
Short-circuit protection for type of as-
signment 2 according to
IEC 60947-4-1 F- 6
Short-circuit protection with fuses for mo-
tor feeders for short-circuit currents up
to 100 kA and 690 V D-24
Signal conditioner 11-15, 11-16, 11-17
Signal conditioner logic modules 11-15
Signal conditioner 1 (and 2, 3, 4) 1-123
Signal conditioner settings 11-17
Signal conditioners 1-21, 11-2
To Next Page
Loading...
Need help?
General
