Name: Agilent Technologies U2000 Series
Brand: Agilent Technologies
Rating: 4 (1 reviews)

Default Chapter3

1 Power Sensor Remote Operation21

Introduction21
Configuring the Remote Interface22
- Interface Selection22
- USB Configuration22
Zeroing and Calibrating the U2000 Series USB Power Sensors23
- Zeroing23
- Calibration23
- Table 1-1 Measure? and Configure Preset States25
Making Measurement25
- Using Measure26
- Using the Configure Command28
- Using the Lower Level Commands33
Using Frequency Dependent Offset Tables35
- Overview35
- Figure 1-1 Frequency Dependent Offset Tables36
- Editing Frequency Dependent Offset Tables37
- Selecting a Frequency Dependent Offset Table40
- Enabling a Frequency Dependent Offset Table40
- Making the Measurement40
Setting the Range and Averaging42
- Averaging42
- Auto Averaging Mode42
- Figure 1-2 Typical Averaged Readings on U2000 Series USB Power Sensors43
- Figure 1-3 Averaging Range Hysteresis43
- Filter Length44
- Range44
Setting Offsets45
- Channel Offsets45
- Figure 1-4 Limits Checking Results46
Setting Measurement Limits46
Setting Limits46
Checking for Limit Failures47
- Table 1-2 Range of Values for Measurement Limits47
- Getting the Best Speed Performance49
Measurement Rate49
Trigger Mode49
Output Format51
Units51
Command Used51
Fast Mode52
- Figure 1-5 How Measurement Are Calculated53
- How Measurements Are Calculated53
- Status Reporting54
The General Status Register Model54
- Figure 1-6 Generalized Status Register Model55
- Figure 1-7 Typical Status Register Bit Changes56
- How to Use Register57
The Condition Polling Method57
- Figure 1-8 Status System58
- Table 1-3 Bit Definitions - Status Byte Register59
- Table 1-4 Bit Definitions - Standard Event Register60
- Table 1-5 Bit Definitions - Questionable Status Registers62
- Table 1-6 Bit Change Conditions for Questionable Status Register62
- Table 1-7 Bit Definitions - Operation Status63
- Table 1-8 Bit Change Conditions for Operation Status64
Status Registers57
Device Status Register65
- Table 1-9 Bit Definitions - Device Status Register65
- Table 1-10 Bit Change Conditions for Device Status Register66
Using the Operation Complete Commands67
- Saving and Recalling Power Sensor Configurations68
How to Save and Recall a Configuration68
- Using Device Clear to Halt Measurements69
- An Introduction to the SCPI Language70
Mnemonic Forms70
- Figure 1-9 Hierarchical Structure of SCPI70
Using a Colon (:)70
- Using "?" Commands71
Using a Semicolon (;)71
Using a Comma (,)71
Using Whitespace71
Syntax Conventions72
Syntax Diagram Conventions72
- Using "*" Commands72
- Figure 1-10 Format of <Character_Data73
SCPI Data Types73
- Figure 1-11 Format of <Non-Decimal Numeric75
- Figure 1-12 Format of <NR176
- Figure 1-13 Format of <NR276
- Figure 1-14 Format of <NR377
- Figure 1-15 Format of <String78
Input Message Terminators79
- SCPI Compliance Information80
- Summary of Commands81

2 Measurement Commands84

Figure 2-1 Measurement Display Calculate Block Window85

3 Calculate Subsystem103

4 Calibration Subsystem126

5 Format Subsystem139

6 Memory Subsystem143

7 Sense Subsystem177

8 Service Subsystem245

10 System Subsystem267

11 Trigger Subsystem281

12 UNIT Subsystem Unit[1]:Power <Amplitude_Unit311

Figure 12-1 Measurement Display UNIT Block Window312
- Unit[1]:Power <Amplitude_Unit313

13 IEEE 488.2 Command Reference316

Agilent Technologies U2000 Series Guide

Table of Contents

Other manuals for Agilent Technologies U2000 Series

Questions and Answers:

Agilent Technologies U2000 Series Specifications

Related product manuals

Brand	Agilent Technologies
Model	U2000 Series
Category	Accessories
Language	English