D-Link xStack DGS-3420 Series - Page 151

xStack® DGS-3420 Series Layer 2 Managed Stackable Gigabit Switch CLI Reference Guide
146
Format
config egress_flow_meter [profile_id <value 1-4> | profile_name <name 1-32>] access_id
<value 1-128> [rate <value 0-1048576> {burst_size <value 0-131072>} rate_exceed [drop_packet
| remark_dscp <value 0-63>] | tr_tcm cir <value 0-1048576> {cbs <value 0-131072>} pir <value 0-
1048576> {pbs <value 0-131072>} {[color_blind | color_aware]} {conform [permit | replace_dscp
<value 0-63>] {counter [enable | disable]}} exceed [permit {replace_dscp <value 0-63>} | drop]
{counter [enable | disable]} violate [permit {replace_dscp <value 0-63>} | drop] {counter [enable
| disable]} | sr_tcm cir <value 0-1048576> cbs <value 0-131072> ebs <value 0-131072>
{[color_blind | color_aware]} {conform [permit | replace_dscp <value 0-63>] {counter [enable |
disable]}} exceed [permit {replace_dscp <value 0-63>} | drop] {counter [enable | disable]}
violate [permit {replace_dscp <value 0-63>} | drop] {counter [enable | disable]} | delete]
Parameters
profile_id - Specifies the profile ID.
<value 1-4> - Enter the profile ID used here. This value must be between 1 and 4.
profile_name - Specifies the name of the profile.
<name 1-32> - Enter the profile name used here. This name can be up to 32 characters long.
access_id - Specifies the access ID.
<value 1-128> - Enter the access ID used here. This value must be between 1 and 128.
rate - This specifies the rate for single rate two-color mode. Specify the committed bandwidth in Kbps
for the flow. The value m and n are determined by the project.
<value 0-1048576> - Enter the rate for single rate two-color mode here. This value must be
between 0 and 1048576.
burst_size - (Optional) This specifies the burst size for the single rate “two color” mode. The unit is
Kbytes.
<value 0-131072> - Enter the burst size value here. This value must be between 0 and 131072.
rate_exceed - This specifies the action for packets that exceed the committed rate in single rate “two
color” mode. The action can be specified as one of the following:
drop_packet - Drop the packet immediately.
remark_dscp - Mark the packet with a specified DSCP. The packet is set to have the higher drop
precedence.
<value 0-63> - Enter the remark DSCP value here. This value must be between 0 and 63.
tr_tcm - Specify the “two rate three color mode”.
cir - Specifies the two rate three color mode used.
<value 0-1048576> - Enter the two rate three color mode value here. This value must be
between 0 and 1048576.
cbs - (Optional) Specifies the “Committed Burst Size”. The unit is Kbytes. That is to say, 1 means
1Kbytes. This parameter is an optional parameter. The default value is 4*1024.
<value 0-131072> - Enter the comitted burst size value here. This value must be between 0
and 131072.
pir - Specifies the “Peak Information Rate”. The unit is in Kbps. PIR should always be equal to or
greater than CIR.
<value 0-1048576> - Enter the peak information rate value here. This value must be between
0 and 1048576.
pbs - (Optional) Specifies the “Peak Burst Size”. The unit is in Kbytes.
<value 0-131072> - Enter the peak burst size value here. This value must be between 0 and
131072.
color_blind - (Optional) Specify the meter mode to be color-blind. The default is color-blind mode.
color_aware - (Optional) Specify the meter mode to be color-aware. When this code is specified,
user could set the “in-coming packet color” by using command “config color_aware”. The final
color of packet is determined by the initial color of packet and the metering result.