GW Instek PEL-2000A Series - Frame Link Connection

GETTING STARTED
55
Frame Link Connection
Background
Frame link control involves connecting multiple
mainframes using the frame link connections. Up
to 4 slave mainframes can be connected to the
master mainframe. The first mainframe (master)
can be used to control the other slave frames.
There is a delay time of 2µs between the master
and first slave mainframe, and 4µs, 6µs, and 8µs to
the second, third, and fourth slave mainframes,
respectively. The connectors used are standard
MIL 20-pin connectors. For pin arrangement, see
page 286. The frame link cable (part no. GTL-249)
is an optional accessory, see page 17 for details.
Frame Link
Connection
AWG 24
STRIP GAUGE
10.0 mm
1
CH CONT 1
1
CH CONT 2
1
CH CONT 3
1
CH CONT 4
1
CH CONT 5
1
CH CONT 6
1
CH CONT 7
1
CH CONT 8
SER. NO. LB
2
1
FRAME CONT
GO / NG OUTPUT
GPIB
RS232C
DISCONNECT POWER CORD
BEFORE REPLACING FUSE
AC input voltage range:
100-120Vac/ 200-240Vac
Frequency: 50/ 60Hz
Power rating: 250VA Max
250V
T 3.15A
REPLACE FUSE
FUSE RATING
AS SPECIFIED
WARNING
TO AVOID ELECTRIC SHOCK THE POWER CORD PROTECTIVE
DO NOT REMOVE COVERS. REFER SERVICING TO QUALIFIED PERSONNEL.
250V FUSE OF THE SPECIFIED TYPE AND RATING.
FOR CONTINUED FIRE PROTECTION. REPLACE FUSE ONLY WITH
NO OPERATOR SERVICEABLE COMPONENTS INSIDE.
GROUNDING CONDUCTOR MUST BE CONNECTED TO GROUND.
AWG 24
STRIP GAUGE
10.0 mm
1
CH CONT 1
1
CH CONT 2
1
CH CONT 3
1
CH CONT 4
1
CH CONT 5
1
CH CONT 6
1
CH CONT 7
1
CH CONT 8
SER. NO. LB
2
1
FRAME CONT
GO / NG OUTPUT
GPIB
RS232C
DISCONNECT POWER CORD
BEFORE REPLACING FUSE
AC input voltage range:
100-120Vac/ 200-240Vac
Frequency: 50/ 60Hz
Power rating: 250VA Max
250V
T 3.15A
REPLACE FUSE
FUSE RATING
AS SPECIFIED
WARNING
TO AVOID ELECTRIC SHOCK THE POWER CORD PROTECTIVE
DO NOT REMOVE COVERS. REFER SERVICING TO QUALIFIED PERSONNEL.
250V FUSE OF THE SPECIFIED TYPE AND RATING.
FOR CONTINUED FIRE PROTECTION. REPLACE FUSE ONLY WITH
NO OPERATOR SERVICEABLE COMPONENTS INSIDE.
GROUNDING CONDUCTOR MUST BE CONNECTED TO GROUND.
AWG 24
STRIP GAUGE
10.0 mm
1
CH CONT 1
1
CH CONT 2
1
CH CONT 3
1
CH CONT 4
1
CH CONT 5
1
CH CONT 6
1
CH CONT 7
1
CH CONT 8
SER. NO. LB
2
1
FRAME CONT
GO / NG OUTPUT
GPIB
RS232C
DISCONNECT POWER CORD
BEFORE REPLACING FUSE
AC input voltage range:
100-120Vac/ 200-240Vac
Frequency: 50/ 60Hz
Power rating: 250VA Max
250V
T 3.15A
REPLACE FUSE
FUSE RATING
AS SPECIFIED
WARNING
TO AVOID ELECTRIC SHOCK THE POWER CORD PROTECTIVE
DO NOT REMOVE COVERS. REFER SERVICING TO QUALIFIED PERSONNEL.
250V FUSE OF THE SPECIFIED TYPE AND RATING.
FOR CONTINUED FIRE PROTECTION. REPLACE FUSE ONLY WITH
NO OPERATOR SERVICEABLE COMPONENTS INSIDE.
GROUNDING CONDUCTOR MUST BE CONNECTED TO GROUND.
2
1
FRAME CONT
2
2
1
FRAME CONT
1
Output
Master
(FRM)
Output
Input
Input
Slave
(FRS)
Slave
(FRS)