Honeywell UDC3500 User Manual

Index
3/07 UDC3500 Universal Digital Controller Product Manual 437
12 Index
8 Segment Characterizers ..........................3, 216
A
Aborting Accutune...........................................212
Accutune – Register Addresses......................383
Accutune Error Codes.....................................211
Accutune III.................................................5, 204
Accutune Set Up Group....................................72
Alarm Blocking................................................171
Alarm Hysteresis.............................................168
Alarm Outputs...................................................15
Alarm Prompts For Healthwatch Option..........166
Alarm Prompts For Two Loops/Cascade Option
....................................................................165
Alarm Relay Output Failure.............................323
Alarm Relays.....................................................19
Alarm Setpoints...............................................234
Alarm Setpoints Display..................................234
Alarms.................................................................3
Alarms – Register Addresses..........................421
Alarms For Software Options..........................165
Alarms Set Up Group......................................164
Algorithm – Register Addresses......................385
Algorithm Set Up Group....................................77
Ambient Temperature .......................................16
Analog Input Failure........................................325
Analog Input Signal Failure Operation ..............13
Analog Inputs................................................2, 13
Annunciators...................................................196
Application Related Problems.........................306
Approval Body Options .......................................5
Atmospheric Pressure Compensation...............86
Auto Bias.........................................................145
Auto/Manual Key.............................................195
Auto/Manual Station............................................4
Auto/Manual Station Mode
..............................224
Automatic Cascade.........................................200
Automatic Tune...............................................208
Automatic With Local Setpoint ........................200
Automatic With Remote Setpoint ....................200
Autotune Is Complete......................................212
Auxiliary Output...................................................4
Auxiliary Output Range...................................152
B
Background Tests...........................................309
Baud Rate.......................................................161
Bias.................................118, 121, 124, 127, 130
Blended Tune..................................................209
Burnout Protection ..........118, 122, 125, 127, 130
C
Calibration Mode.....................................291, 303
Calibration Steps.............................................276
Carbon Potential ...............................86, 240, 241
Carbon Potential .....................................192, 238
Carbon Potential Selections..............................83
Cascade Control .............................................228
CE Conformity (Europe)....................................10
CE Mark............................................................. 5
Changing Control Modes.................................201
Changing The Local Setpoints ........................202
Characterizer...............................................92, 94
Clock – Register Addresses............................431
Combinational Inputs ......................................... 3
Communications ................................................ 4
Communications – Register Addresses ..........419
Communications Failure..................................326
Communications Selection..............................160
Communications Set Up Group.......................160
Comparator Gates...........................................217
Computer Setpoint ..........................................353
Computer Setpoint Bias ..................................162
Computer Setpoint Ratio.................................162
Computer Setpoint Units.................................162
Configuration.....................................................43
Configuration Data ..........................................345
Configuration Parameters ...............................356
Configuration Procedure ...................................49
Configuration Prompt Hierarchy........................45
Configuration Record Sheet............................184
Control – Register Addresses .........................409
Control 2 Set Up Group...................................141
Control Algorithm ..............................................77
Control And Alarm Relay Contact Information...19
Control Loop 2 – Register Addresses..............412
Control Mode Definitions.................................200
Control Modes.................................................200
Control Relays...................................................19
Control Set Up Group......................................132
Control/Alarm Circuit Wiring..............................22
Controller Dropoff Value..........................138, 147
Controller Failure Symptoms...........................314
Controller Grounding.........................................22
Controller Output Types....................................14
Counter ...........................................................174
Current Duplex........................................106, 109
Current Output ....................................34, 36, 111
Current Output 2 .............................................148
Current Output 3 .............................................152
Current Output Calibration ..............294, 296, 298
Current Output Failure Symptoms...................316
Current Simplex ......................................106, 109
Current/Time Duplex...............................106, 109
Current/Time Or Time/Current Proportional
Output Failure .............................................322
Customer Support...........................................307
Cycle Number .................................................350
Cycle Time (Cool) .......................................52, 56
Cycle Time (Heat) .......................................52, 56
Cycles Remaining ...........................................350

Honeywell UDC3500 Specifications

General

Brand	Honeywell
Model	UDC3500
Category	Controller
Language	English