LOYTEC L-INX - Page 300

To Next Page

To Previous Page

L-INX User Manual 300 LOYTEC

Version 4.0 LOYTEC electronics GmbH

As useful information, the MAC address of the conflicting host is shown. If the information

about this conflict shall be cleared, enter ‗y‘. If ‗n‘ is selected, the conflict will show up

again the next time this menu is entered.

Main Page

Default Chapter3
- Table of Contents3
1 Introduction17
- Overview17
- Cea-709.118
- Bacnet19
- M-Bus20
- Modbus20
- Liob21
- L-INX Models21
- Scope22
2 Quick-Start Guide23
- Hardware Installation23
- Configuration of the LINX24
- Getting Started with the L-INX Configurator28
- Configuration of the L-IOB I/O Modules29
- Getting Started with Logicad31
- Connect with an OPC XML-DA Client36
- Reset to Factory Defaults36
3 Hardware Installation37
- Enclosure37
- Product Label40
- Mounting42
- LED Signals43
- Status Button46
  - Resetting Forwarding Tables46
- LCD Display and Jog Dial47
- DIP Switch Settings48
- Terminal Layout and Power Supply48
  - Linx-10X/11X48
  - Linx-20X/21X48
- Wiring49
4 Web Interface53
- Device Information and Account Management53
- Device Configuration55
- Device Statistics75
- L-Web82
- Reset, Contact, Logout82
5 Concepts84
- Data Points84
- Connections87
- AST Features88
- Technology93
- Bacnet Technology96
- IEC61131 Variables98
6 The L-INX Configurator99
- Installation99
  - Software Installation99
  - Registration as an LNS Plug-In99
  - Operating Modes101
- Data Point Manager101
  - Folder List101
  - Network Port Folders103
  - Data Point List103
  - Property View104
  - Managing Multistate Maps106
  - Organizing Favorites107
  - Properties107
  - Bacnet Properties108
- Project Settings109
  - General109
  - Data Point Naming Rules110
  - Settings110
  - AST Settings111
  - Bacnet Settings113
  - Device Configuration114
  - Logicad115
- Workflows for CEA-709116
  - Involved Configuration Files116
  - Configure with LNS116
  - Configure Without LNS117
  - Configure Without LNS Using Bindings118
  - Replace a L-INX119
  - Adding the L-INX to LNS120
  - Replace a L-INX in LNS122
- Workflows for Bacnet125
  - Involved Configuration Files125
  - Engineer On-Line126
  - Engineer Off-Line126
  - Replace a L-INX127
- Using the L-INX Configurator128
  - Starting Stand-Alone128
  - Uploading the Configuration129
  - Create User Registers129
  - Configuration Download130
  - Upload the System Log131
  - Backup and Restore132
- Configuration133
  - Starting as an LNS Plug-In133
  - Scanning for Network Variables134
  - Importing Network Variables135
  - Scanning Nvs Online from the Network136
  - Select and Use Network Variables138
  - Change the NV Allocation138
  - Create Static Nvs139
  - Create External Nvs140
  - Configuration Download over LNS142
  - Enable Legacy NM Mode143
  - Build XIF for Port Interface144
  - Upload Dynamic Nvs from Device144
- Advanced CEA-709 Configuration145
  - Import Devices from XIF Templates145
  - Install Unconfigured Devices145
  - Using Feedback Data Points146
  - Working with Configuration Properties147
  - Working with Unvts, Ucpts148
- Bacnet Configuration149
  - Scan for Bacnet Objects149
  - Import from EDE File150
- Use Imported Bacnet Objects151
- Edit a Client Mapping151
- Create Server Object152
- Export Server Objects to an EDE File153
- Map Other Properties than Present_Value154
- Enable International Character Support155
- Connections155
  - Create a New Connection155
  - Create Connections from a CSV File157
  - Modify Connections157
  - Connection Overview158
- E-Mail Templates158
  - Create an E-Mail Template158
  - Trigger E-Mails159
  - Attachments160
  - Limit E-Mail Send Rate161
- Local Schedule and Calendar161
  - Create a Local Calendar161
  - Create Calendar Pattern162
  - Create a Local Scheduler162
  - Configure Scheduled Data Points163
  - Configure Daily Schedules164
  - Configure Exception Days166
  - Configure Embedded Exceptions167
  - Configure Control Data Points168
  - Using the Snvt_Tod_Event168
  - Using the Local Scheduler169
- Local Alarming169
  - Create an Alarm Server169
  - Create an Alarm Condition170
  - Deliver Alarms Via E-Mail172
  - Create an Alarm Log173
- Local Trending174
  - Create a Local Trend174
  - Configure Trended Data Points175
  - Trend Triggers176
  - Download Trend Data in CSV Format177
  - Deliver Trend Data Via E-Mail177
- Remote AST Objects178
  - Remote Scheduler and Calendar178
  - Alarm Clients179
  - Math Objects180
    - Create a Math Object180
    - Editing a Math Object181
7 The CEA-709 Router182
- Router182
- Device of the Router184
- Firewall and NAT Router Configuration187
- Multi-Cast Configuration191
- Remote LPA Operation192
- Advanced Topics194
8 The LINX-100 RNI196
- RNI Function196
- Remote LPA Operation196
9 OPC Server197
- XML-DA OPC Server197
- Using L-WEB203
- Using the OPC Bridge206
- Using Custom Web210
10 Bus211
- Introduction211
- Hardware Installation211
  - Console Connector211
  - Extension Port212
- M-Bus Network212
- Web Interface213
- Configurator215
- M-Bus Workflow217
  - Offline Engineering218
  - Online Engineering218
- Using the Configurator for M-Bus219
11 Modbus235
- Introduction235
- Modbus Network235
- Web Interface236
- Configurator238
- Using the Configurator for Modbus242
12 Iec 61131255
- Overview255
- Installing Logicad255
- IEC61131 Project Files256
- Working with Logicad257
- Workflows for the LINX264
- Additional Features274
13 Operating Interfaces277
- Common Interface277
- Interface279
- Bacnet Interface283
14 Network Media291
- M-Bus292
- Modbus RS-485292
15 Firmware Update293
- Firmware Update Via the Configurator293
- Firmware Update Via the Console295
16 Troubleshooting297
- Technical Support297
- Statistics on the Console297
17 Application Notes301
- The LSD Tool301
- Use of Static, Dynamic, and External Nvs on a Device301
18 Specifications302
- Physical Specifications302
  - Linx-10X/11X/20X/21X302
  - Linx-12X/15X/22X302
- Resource Limits303
19 References304
20 Revision History305

LOYTEC L-INX - Page 300

Table of Contents