Parker 590+ series - Page 305

Parameter Specification Tables C-15
DC590+ Series DC Digital Drive
Tag Mn MMI Block Name MMI Parameter Name Minimum Maximum Default Units Range Notes
434 m2 TORQUE CALC. OVER WIND 0 1 1
0: DISABLED
1: ENABLED
V1 W0
435 m3 LINK 32 POS. I CLAMP 0 1276 0 V0 W2
436 m4 LINK 33 NEG. I CLAMP 0 1276 0 V0 W2
437 m5 DIAMETER CALC. REEL SPEED -105.00 105.00 0.00 % V1 W0
438 m6 DIAMETER CALC. TAPER -100.00 100.00 0.00 % V1 W0
439 m7 DIAMETER CALC. TENSION SPT. 0.00 100.00 0.00 % V1 W0
440 m8 DIAMETER CALC. TENSION TRIM -100.00 100.00 0.00 % V1 W0
441 m9 DIAMETER CALC. TOT.TENS.DEMAND 0.00 0.00 0.00 % V1 W4
442 ma LINK 34 TAPER 0 1276 0 V0 W2
443 mb SETPOINT SUM 2 INPUT 1 -300.00 300.00 0.00 % V1 W0
444 mc SETPOINT SUM 2 INPUT 0 -300.00 300.00 0.00 % V1 W0
445 md SETPOINT SUM 2 INPUT 2 -300.00 300.00 0.00 % V1 W0
446 me SETPOINT SUM 2 RATIO 1 -3.0000 3.0000 1.0000 V0 W0
447 mf SETPOINT SUM 2 RATIO 0 -3.0000 3.0000 1.0000 V0 W0
448 mg SETPOINT SUM 2 DIVIDER 0 -3.0000 3.0000 1.0000 V0 W0
449 mh SETPOINT SUM 2 LIMIT 0.00 200.00 105.00 % V0 W0
450 mi LINK 35 SETPOINT SUM 2 0 1276 0 V0 W2
451 mj SETPOINT SUM 2 SPT SUM OUTPUT 0.00 0.00 0.00 % V1 W4
452 mk DIAMETER CALC. TAPERED DEMAND 0.00 0.00 0.00 % V1 W4
453 ml DIAMETER CALC. RAMP RATE 0.1 600.0 5.0 s V1 W0
454 mm LINK 5 SOURCE TAG -1276 1276 0 V0 W2
455 mn LINK 5 DESTINATION TAG 0 1276 0 V0 W2
456 mo LINK 6 SOURCE TAG -1276 1276 0 V0 W2
457 mp LINK 6 DESTINATION TAG 0 1276 0 V0 W2
458 mq LINK 7 SOURCE TAG -1276 1276 0 V0 W2
459 mr LINK 7 DESTINATION TAG 0 1276 0 V0 W2
460 ms LINK 8 SOURCE TAG -1276 1276 0 V0 W2
461 mt LINK 8 DESTINATION TAG 0 1276 0 V0 W2
462 mu DIAMETER CALC. RESET VALUE 0.00 100.00 10.00 % V1 W0
463 mv DIAMETER CALC. EXTERNAL RESET 0 1 0
0: DISABLED
1: ENABLED
V1 W0
464 mw ANALOG OUTPUT 1 OFFSET -100.00 100.00 0.00 % V0 W0
465 mx ANALOG OUTPUT 2 OFFSET -100.00 100.00 0.00 % V0 W0