Parker 590+ series - Page 304

C-14 Parameter Specification Tables
DC590+ Series DC Digital Drive
Tag Mn MMI Block Name MMI Parameter Name Minimum Maximum Default Units Range Notes
403 l7 PID FILTER T.C. 0.000 10.000 0.100 s V1 W0
404 l8 PROFILED GAIN PROP. GAIN 0.0 100.0 1.0 V1 W0
405 l9 PID POSITIVE LIMIT 0.00 105.00 100.00 % V1 W0
406 la PID NEGATIVE LIMIT -105.00 0.00 -100.00 % V1 W0
407 lb PID O/P SCALER(TRIM) -3.0000 3.0000 0.2000 V1 W0
408 lc PID ENABLE 0 1 1
0: DISABLED
1: ENABLED
V1 W0
409 ld PID INT. DEFEAT 0 1 0
0: OFF
1: ON
V1 W0
410 le PID INPUT 1 -300.00 300.00 0.00 % V1 W0
411 lf PID INPUT 2 -300.00 300.00 0.00 % V1 W0
412 lg PID RATIO 1 -3.0000 3.0000 1.0000 V1 W0
413 lh PID RATIO 2 -3.0000 3.0000 1.0000 V1 W0
414 li PID DIVIDER 2 -3.0000 3.0000 1.0000 V1 W0
415 lj PID PID ERROR 0.00 0.00 0.00 % V1 W4
416 lk PID PID CLAMPED 0 1 0 V1 W4
417 ll PID PID OUTPUT 0.00 0.00 0.00 % V1 W4
418 lm PID DIVIDER 1 -3.0000 3.0000 1.0000 V1 W0
419 ln SETPOINT SUM 1 DIVIDER 1 -3.0000 3.0000 1.0000 V1 W0
420 lo SETPOINT SUM 1 DIVIDER 0 -3.0000 3.0000 1.0000 V0 W0
421 lp CURRENT LOOP MAIN CURR. LIMIT 0.00 200.00 110.00 % V0 W0
422 lq RAMPS RESET VALUE -300.00 300.00 0.00 % V1 W0
423 lr SETPOINT SUM 1 INPUT 2 -300.00 300.00 0.00 % V1 W0
424 ls DIAMETER CALC. LINE SPEED -105.00 105.00 0.00 % V1 W0
425 lt DIAMETER CALC. MIN DIAMETER 0.00 100.00 10.00 % V1 W0
426 lu DIAMETER CALC. MIN SPEED 0.00 100.00 5.00 % V1 W0
427 lv DIAMETER CALC. DIAMETER 0.00 0.00 0.00 % V1 W4
428 lw DIAMETER CALC. MOD OF LINE SPD 0.00 0.00 0.00 % V0 W4
429 lx DIAMETER CALC. MOD OF REEL SPD 0.00 0.00 0.00 % V0 W4
430 ly DIAMETER CALC. UNFILT DIAMETER 0.00 0.00 0.00 % V0 W4
431 lz LINK 31 DIAMETER 0 1276 0 V0 W2
432 m0 TORQUE CALC. TORQUE DEMAND -200.00 200.00 0.00 % V1 W0
433 m1 TORQUE CALC. TENSION ENABLE 0 1 1
0: DISABLED
1: ENABLED
V1 W0