Parker AC30 series - Page 446

C-264 Parameter Reference
AC30 series Variable Speed Drive
1886
Actual Control Type
Monitor::Motor and Drive
Parameters::Control Mode::Control Mode
USINT
(enum)
Same as PNO 1533
NEVER
ENGINEER
4
04299
1887
Start Align Done
Same as PNO 1886
BOOL
NEVER
TECHNICIAN
4
04301
1891
SNTP Server Enable
Parameters::Base Comms::SNTP Server
BOOL
FALSE
ALWAYS
TECHNICIAN
04309
1892
Encoder Speed
Same as PNO 1878
REAL
x.
Min to Max
RPM
NEVER
OPERATOR
4
04311
1893
Encoder Speed Percent
Parameters::System Board::SB Encoder
REAL
x.xx
Min to Max
%
NEVER
OPERATOR
4
04313
1894
Motor Count Reset
Same as PNO 1874
BOOL
FALSE
ALWAYS
TECHNICIAN
2,4
04315
1895
Calibration Error
Parameters::System Board::SB Encoder
USINT
(enum)
0:NONE
1:MOTOR NOT STOPPED
2:ENDAT TIMEOUT
3:ENDAT READ
4:ENDAT CHECKSUM FAIL
5:SINCOS AND ENDAT POS1
6:SINCOS AND ENDAT POS2
7:SINCOS AND ENDAT POS3
8:SINCOS AND ENDAT POS4
9:SINCOS AND ENDAT POS5
10:SINCOS AND ENDAT POS6
11:TIMEOUT
12:MASK CREATION
13:HW MISMATCH1
14:HW MISMATCH2
15:FAULTY ENCODER
16:WRONG ENCODER LINES
17:WRONG ENCODER TYPE
18:WARNING
NEVER
TECHNICIAN
4
04317
1896
Absolute Calib Status
Parameters::System Board::SB Encoder
USINT
(enum)
0:CAL NOT REQUIRED
1:DRIVE NOT STOPPED
2:MOTOR NOT STOPPED
3:ENDAT FAULT
4:CALIB IN PROGRESS
5:RECOVERING LOAD POS
6:CALIB COMPLETED
7:CALIB LOST
8:CALIB FAILED
9:CALIB WARNING
NEVER
TECHNICIAN
4
04319
1897
Calib Fail Retry
Same as PNO 1874
BOOL
FALSE
STOPPED
TECHNICIAN
2,4
04321
1898
Motor Count
Parameters::System Board::SB Encoder
DINT
Min to Max
NEVER
TECHNICIAN
1,4
04323
3000
Input Mapping
Setup::Communications::Base PROFINET
Parameters::Base Comms::Fieldbus Mapping
ARRAY[0..31]
CONFIG
ENGINEER
06527
3001
Input Mapping[0]
Same as PNO 3000
UINT
0627
0000 to 3145
CONFIG
ENGINEER
06529
3002
Input Mapping[1]
Same as PNO 3000
UINT
0681
0000 to 3145
CONFIG
ENGINEER
06531
3003
Input Mapping[2]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06533
3004
Input Mapping[3]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06535
3005
Input Mapping[4]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06537
3006
Input Mapping[5]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06539
3007
Input Mapping[6]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06541
3008
Input Mapping[7]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06543
3009
Input Mapping[8]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06545
3010
Input Mapping[9]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06547
3011
Input Mapping[10]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06549
3012
Input Mapping[11]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06551
3013
Input Mapping[12]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06553
3014
Input Mapping[13]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06555
3015
Input Mapping[14]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06557
3016
Input Mapping[15]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06559
3017
Input Mapping[16]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06561
3018
Input Mapping[17]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06563
3019
Input Mapping[18]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06565
3020
Input Mapping[19]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06567
3021
Input Mapping[20]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06569
3022
Input Mapping[21]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06571
3023
Input Mapping[22]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06573
3024
Input Mapping[23]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06575
3025
Input Mapping[24]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06577
3026
Input Mapping[25]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06579
3027
Input Mapping[26]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06581
3028
Input Mapping[27]
Same as PNO 3000
UINT
0000
0000 to 3145
CONFIG
ENGINEER
06583