Steris Vision 1321 - Page 10

9
Operator Manual
Vision® 1300 Series
920515770_J
8.17 Alarm# 15 Reservoir #1 Water Temperature Too High.......................................................165
8.18 Alarm# 16 Reservoir #1 RTD Defective ................................................................................165
8.19 Alarm# 17 Reservoir Overflow ..............................................................................................166
8.20 Alarm# 18 Reservoir #1 Hot Water Not Filling ....................................................................166
8.21 Alarm# 19 Reservoir #1 Pure Water Not Filling...................................................................167
8.22 Alarm# 20 Reservoir #2 Hot Water Not Filling ....................................................................167
8.23 Alarm# 21 Reservoir #2 Cold Water Not Filling ...................................................................168
8.24 Alarm# 22 Reservoir #3 Hot Water Not Filling ....................................................................168
8.25 Alarm# 23 Reservoir #1 Level Sensors Defective................................................................169
8.26 Alarm# 24 Reservoir #2 Level Sensors Defective................................................................169
8.27 Alarm# 25 Reservoir #3 Level Sensors Defective................................................................170
8.28 Alarm# 26 Reservoir #1 Draining or Transfer Malfunction .................................................170
8.29 Alarm# 27 Reservoir #2 Draining or Transfer Malfunction .................................................171
8.30 Alarm# 28 Reservoir #3 Draining or Transfer Malfunction .................................................171
8.31 Alarm #29 Chamber Pressure Abnormal ..............................................................................171
8.32 Alarm# 30 Dosing System Communication Failure .............................................................172
8.33 Alarm# 31 Chemical #1 Low Level ........................................................................................172
8.34 Alarm# 32 Chemical #2 Low Level ........................................................................................173
8.35 Alarm# 33 Chemical #3 Low Level ........................................................................................173
8.36 Alarm# 34 Chemical #4 Low Level ........................................................................................174
8.37 Alarm# 35 Chemical #5 Low Level ........................................................................................174
8.38 Alarm# 36 Compressed Air Not Detected ............................................................................175
8.39 Alarm# 37 Reservoir #1 Too Long to Heat...........................................................................175
8.40 Alarm# 38 Water Recirculation Pressure Switch Defective ................................................176
8.41 Alarm# 39 PV Chemical Injection with Pump #1 Out of Range ..........................................176
8.42 Alarm# 40 PV Chemical Injection with Pump #2 Out of Range ..........................................177
8.43 Alarm# 41 PV Chemical Injection with Pump #3 Out of Range ..........................................177
8.44 Alarm# 42 PV Thermal Temperature Out of Range.............................................................178
8.45 Alarm# 48 Over Temperature Switch Tripped......................................................................179
8.46 Alarm# 49 Dosing System Software Outdated....................................................................179
8.47 Alarm# 50 Analog Sensor Calibrations have been Reset to Factory Default
Values ......................................................................................................................................180
8.48 Alarm# 51 Cycles Returned to Factory Default Values, Warn Supervisor! ........................180
8.49 Warning# 1 Hot Water Pressure Below Requirement.........................................................180
8.50 Warning# 2 Pure Water Pressure Below Requirement.......................................................181
8.51 Warning# 3 Hot Water Pressure Above Requirement.........................................................181
8.52 Warning# 4 Pure Water Pressure Above Requirement .......................................................181
8.53 Warning# 5 Cold Water Pressure Below Requirement .......................................................182
8.54 Warning# 6 Cold Water Pressure Above Requirement........................................................182
8.55 Warning# 7 Cycle Parameters Have Been Reset to Factory Default Values .....................182
8.56 Warning# 8 Cycle Chemical Injection Rates Have Been Reset to Factory Default
Values ......................................................................................................................................183
8.57 Warning# 9 Temperature Not Reached by Reservoir #1 During DECONTAM Cycle
Wash........................................................................................................................................183
8.58 Windows Message: SterisHMI.exe is not responding..........................................................183
8.59 Bar code reader (accessory) does not operate properly ......................................................184
8.60 Chamber does not drain properly..........................................................................................184
8.61 Chemical leaks from mechanical core dosing system .........................................................184
8.62 Display shows blank red screen with an error message .....................................................185