Need help?Do you have a question about the TP-Link JetStream T3700G-28TQ and is the answer not in the manual?
General| Switch type | Managed |
|---|---|
| Switch layer | L2/L3 |
| Web-based management | Yes |
| Console port | RJ-45 |
| Combo SFP ports quantity | 4 |
| SFP+ module slots quantity | 2 |
| Basic switching RJ-45 Ethernet ports type | Gigabit Ethernet (10/100/1000) |
| Basic switching RJ-45 Ethernet ports quantity | 24 |
| Networking standards | IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Copper ethernet cabling technology | 10BASE-T, 100BASE-T, 100BASE-TX, 1000BASE-TX, 1000BASE-T |
| DHCP features | DHCP Option 82, DHCP client, DHCP relay, DHCP server, DHCP snooping |
| Security algorithms | 802.1x RADIUS, SSH, SSH-2, SSL/TLS |
| Jumbo frames | 10240 |
| Forwarding rate | 95.2 Mpps |
| MAC address table | 32000 entries |
| Packet buffer memory | 2 MB |
| Number of IP interfaces | 128 |
| Number of static routes | 256 |
| Fiber ethernet cabling technology | 100BASE-FX, 10GBASE-LR, 10GBASE-SR |
| Form factor | 1U |
| Certification | CE, FCC, RoHS |
| Product color | Black |
| Number of fans | 4 fan(s) |
| Power source | AC |
| AC input voltage | 110 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (max) | 63 W |
| Heat dissipation | 214.96 BTU/h |
| Storage temperature (T-T) | -40 - 70 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 90 % |
| Operating relative humidity (H-H) | 10 - 90 % |
| Package depth | 590 mm |
| Package width | 580 mm |
| Package height | 120 mm |
| Package weight | 8230 g |
Weight and Dimensions| Depth | 330 mm |
|---|---|
| Width | 440 mm |
| Height | 44 mm |
Provides methods to log on to the switch and access the CLI via console or remote connections.
Details steps for connecting via console, including Hyper Terminal setup and port configuration.
Explains how to set a password for entering Privileged EXEC Mode via console connection.
Describes Telnet login modes (local and standard) and steps for connecting to the switch.
Recommends Putty for SSH, detailing password and key authentication modes for setup.
Outlines the different CLI command modes: User EXEC, Privileged EXEC, Global Configuration, etc.
Explains the two security levels (User and Admin) and their access privileges.
Details formatting conventions, special characters, and parameter formats used in the guide.
Command to access Privileged EXEC Mode from User EXEC Mode.
Command to set the password for accessing Privileged EXEC Mode from User EXEC Mode.
Command to return to User EXEC Mode from Privileged EXEC Mode.
Command to access Global Configuration Mode from Privileged EXEC Mode.
Command to return to the previous mode from the current configuration mode.
Command to return to Privileged EXEC Mode from any configuration mode.
Command to show the last 20 commands entered in the current mode.
Command to clear the history of commands entered in the current mode.
Command to specify stack member number and its priority for stack management.
Command to modify the member number of a specified stack member.
Command to configure the stack's authentication mode (MD5 or simple).
Command to customize the stack's name for identification.
Command to enable the stack port, allowing it to function as a stack port.
Command to display the current stack's information and status.
Command to create IEEE 802.1Q VLANs and access VLAN Configuration Mode.
Command to create VLAN interfaces and access Interface VLAN Mode.
Command to assign a descriptive string to a VLAN for identification.
Command to configure the link type (access, trunk, general) for ports.
Command to add an access port to an IEEE 802.1Q VLAN or remove it.
Command to add a trunk port to IEEE 802.1Q VLANs or remove it.
Command to add a general port to IEEE 802.1Q VLANs or remove it, specifying tagged/untagged.
Command to configure the Port VLAN ID (PVID) for switch ports.
Command to display the switchport configuration details of Ethernet ports.
Command to display a summarized overview of IEEE 802.1Q VLANs.
Command to display a brief overview of IEEE 802.1Q VLANs.
Command to display detailed information about IEEE 802.1Q VLANs.
Command to create a MAC-based VLAN entry, associating MAC addresses with VLAN IDs.
Command to enable a port for the MAC-based VLAN feature.
Command to display information of MAC-based VLAN entries, filterable by MAC or VLAN.
Command to display the port state of MAC-based VLAN configurations.
Command to create Protocol-based VLAN templates, defining Ethernet types or protocol details.
Command to create Protocol-based VLAN entries and bind them to templates.
Command to enable the Protocol-based VLAN feature for a specified port.
Command to display information about configured Protocol-based VLAN templates.
Command to display information about Protocol-based VLAN entries.
Command to enable the VLAN-VPN function globally for Layer 2 VPN technology.
Command to configure the Global TPID (Tag Protocol Identifier) for VLAN-VPN.
Command to enable the VLAN Mapping feature globally for VLAN-VPN.
Command to add VLAN Mapping entries on specific ports for VLAN-VPN.
Command to configure the VPN port mode (UNI or NNI) for VLAN-VPN.
Command to display the global configuration information of the VLAN VPN.
Command to display information about VLAN Mapping entries for VLAN-VPN.
Command to display the VLAN VPN port type information.
Command to enable the Voice VLAN function for voice data streams.
Command to set the aging time for Voice VLAN entries.
Command to configure the priority for Voice VLANs.
Command to create Voice VLAN OUI entries for device identification.
Command to configure the Voice VLAN mode (manual or auto) for Ethernet ports.
Command to enable the Voice VLAN security feature for Ethernet ports.
Command to display the global configuration information of Voice VLANs.
Command to display the configuration information of Voice VLAN OUIs.
Command to display Voice VLAN configuration for ports or a specified port.
Command to configure a designated VLAN as the primary VLAN of a Private VLAN.
Command to configure a designated VLAN as the community VLAN of a Private VLAN.
Command to configure a designated VLAN as the isolated VLAN of a Private VLAN.
Command to associate primary VLANs with secondary VLANs for Private VLANs.
Command to configure the private VLAN mode (promiscuous or host) for switchports.
Command to associate host-type ports with primary and secondary VLANs.
Command to add promiscuous-type ports to Private VLANs.
Command to display the Private VLAN configuration information of the switch.
Command to display Private VLAN configuration for specified port(s).
Command to enable the GVRP (GARP VLAN Registration Protocol) function globally.
Command to enable the GVRP function for a specific port, typically trunk ports.
Command to configure the GVRP registration type (normal, fixed, forbidden) for ports.
Command to set GVRP timers (leaveall, join, leave) for ports.
Command to display the global GVRP status and configuration.
Command to display GVRP configuration information for specified or all Ethernet ports.
Command to add a port to an EtherChannel Group and configure its mode (static, active, passive).
Command to configure the Aggregate Arithmetic for LAG (src-dst-mac or src-dst-ip).
Command to configure the LACP system priority globally.
Command to configure the LACP port priority globally for interfaces.
Command to display EtherChannel information, either detailed or summarized.
Command to display the Aggregate Arithmetic of LAG.
Command to display LACP information for a specified EtherChannel Group.
Command to display the LACP system priority globally.
Command to add new users or modify existing user information (login, password, access level).
Command to limit user login access based on IP address range.
Command to limit user login access based on MAC address.
Command to limit user login access to specific Ethernet ports.
Command to configure the maximum number of concurrent user logins (Admin/Guest).
Command to configure the idle timeout time for user sessions.
Command to enter Line Configuration Mode for user login settings.
Command to configure connection passwords for console and virtual terminal lines.
Command to configure the login mode for a switch using connection passwords.
Command to configure the login mode using username and password.
Command to display information about currently logged-in users.
Command to display user security configuration details.
Command to manually bind IP, MAC, VLAN, and port numbers for ARP/IP filtering.
Command to globally enable DHCP Snooping for monitoring IP address acquisition.
Command to configure global DHCP Snooping parameters like rate limiting.
Command to enable the Option 82 function of DHCP Snooping.
Command to select operations for DHCP Option 82 field (keep, replace, drop).
Command to enable customized Option 82 settings for DHCP Snooping.
Command to configure customized sub-option Remote ID for DHCP Option 82.
Command to specify customized sub-option Circuit ID for DHCP Option 82.
Command to configure a port as a Trusted Port for DHCP Snooping.
Command to enable MAC Verify feature for DHCP packets.
Command to enable Flow Control for DHCP packets on ports.
Command to enable the Decline Protect feature for DHCP Snooping.
Command to display the IP-MAC-VID-PORT binding table.
Command to display the running status of DHCP Snooping globally.
Command to display DHCP Snooping configuration for Ethernet ports.
Command to globally enable ARP Detection function to prevent ARP cheating.
Command to configure ports as Trusted Ports where ARP detection is unnecessary.
Command to enable ARP Defend function on specific interfaces to mitigate ARP attacks.
Command to configure the ARP speed limit for specified ports.
Command to restore a port to ARP transmit status from ARP filter status.
Command to display global ARP detection configuration, status, and trusted ports.
Command to display interface configuration details for ARP detection.
Command to display the count of illegal ARP packets received.
Command to clear the statistics of illegal ARP packets received.
Command to configure IP Verify Source mode for ports based on IP-MAC binding rules.
Command to display the IP Verify Source configuration information.
Command to globally enable the DoS defend function to protect against attacks.
Command to select the type of DoS Defend (e.g., LAND, SYN-FIN, NULL scan).
Command to display DoS attack information, including status and type.
Command to globally enable the IEEE 802.1X function for LAN port access control.
Command to configure the Authentication Method (PAP or EAP-MD5) for 802.1X.
Command to globally enable the Guest VLAN function for 802.1X.
Command to enable the quiet-period function to limit authentication requests after failure.
Command to configure server and supplicant timeout values for 802.1X.
Command to configure the maximum repeated authentication requests when server is unreachable.
Command to enable the IEEE 802.1X function for a specified port.
Command to enable the guest VLAN function for a specified port.
Command to configure the Control Mode (auto, authorized-force, unauthorized-force) for 802.1X ports.
Command to configure the control type (mac-based or port-based) for 802.1X ports.
Command to configure RADIUS server parameters (IP, port, keys).
Command to enable the accounting feature for RADIUS.
Command to display the global configuration of IEEE 802.1X.
Command to display port-specific or all port configurations for 802.1X.
Command to display the configuration of the RADIUS accounting server.
Command to display the configuration of the RADIUS authentication server.
Command to store system log messages in an internal buffer.
Command to configure the severity level for messages stored in the log buffer.
Command to store log messages in a file on the switch's flash memory.
Command to specify the frequency for synchronizing log files from buffer to flash.
Command to specify the minimum severity level for logs saved to flash.
Command to configure syslog server hosts for receiving logging messages.
Command to save the log file from flash to a TFTP server.
Command to clear syslog messages from the log buffer and flash.
Command to display the configuration of the Local Log, including buffer and file settings.
Command to display the configuration of the log host.
Command to display log information from the log buffer based on severity level.
Command to display log information from the log file based on severity level.
Command to enable the SSH function for secure remote management.
Command to enable specific SSH protocol versions (v1 or v2).
Command to specify the idle-timeout time for SSH connections.
Command to specify the maximum number of concurrent connections to the SSH server.
Command to download SSH key files from a TFTP server to the switch.
Command to remove the SSH public key from the switch.
Command to display the global configuration of SSH and the SSH public key.
Command to enable the SSL function globally for secure HTTPS connections.
Command to download an SSL certificate to the switch from a TFTP server.
Command to download an SSL key to the switch from a TFTP server.
Command to display the global configuration of SSL.
Command to add static MAC address entries for specific VLANs and ports.
Command to configure the aging time for dynamic MAC addresses.
Command to add filtering address entries to block specific MAC addresses.
Command to configure Port Security by limiting learned MAC addresses per port.
Command to display information about all MAC address table entries.
Command to display the aging time of MAC addresses.
Command to display security configuration of Ethernet ports for MAC address limits.
Command to display address configuration of Ethernet ports.
Command to display the total amount of entries in the MAC address table.
Command to display information for a specified MAC address.
Command to display MAC address configuration for a specified VLAN.
Command to manually configure the system time and date.
Command to configure NTP server settings for automatic time synchronization.
Command to select a predefined Daylight Saving Time (DST) configuration.
Command to specify a one-off DST configuration in date mode.
Command to specify DST configuration in recurring mode.
Command to configure the system name (hostname) of the switch.
Command to configure the system location information.
Command to configure the system contact information.
Command to manually configure the IP address and subnet mask for interfaces.
Command to enable DHCP or BOOTP client function for interfaces to obtain IP addresses.
Command to reset the switch's software to factory defaults.
Command to reboot the switch.
Command to save the current running configuration to the startup configuration file.
Command to save the current running configuration to the backup configuration file.
Command to save the current running configuration to a user-defined configuration file.
Command to save the backup configuration file as the startup configuration file.
Command to save the startup configuration file as the backup configuration file.
Command to configure the image file as startup or backup image.
Command to configure the property of the system configuration file.
Command to upload the backup configuration file to a TFTP server.
Command to upload the startup configuration file to a TFTP server.
Command to download configuration file from TFTP server as backup configuration file.
Command to download configuration file from TFTP server as startup configuration file.
Command to download an image file from TFTP server to the switch.
Command to upload an image file from the switch to a TFTP server.
Command to copy and save image files within the stack system.
Command to delete backup image files.
Command to delete configuration files.
Command to upgrade the switch system file via TFTP server.
Command to test network connectivity between the switch and a destination node.
Command to test connectivity of gateways during data path traversal.
Command to perform loopback tests on Ethernet ports to check availability.
Command to display the current system time and its source.
Command to display the Daylight Saving Time (DST) information of the switch.
Command to display the NTP mode configuration information.
Command to display comprehensive system information (name, version, time, etc.).
Command to display system environmental status (fan, power, temperature).
Command to display information about system files on the switch.
Command to display information about system image files.
Command to display the current operating configuration of the system.
Command to display the current boot configuration of the system.
Command to display cable diagnostic results for Ethernet ports.
Command to display the system's CPU utilization over different time intervals.
Command to display the system's memory utilization over different time intervals.
Command to enter fastEthernet interface configuration mode.
Command to configure multiple Fast Ethernet ports simultaneously.
Command to enter gigabitEthernet interface configuration mode.
Command to configure multiple Gigabit Ethernet ports simultaneously.
Command to enter ten-gigabitEthernet interface configuration mode.
Command to configure multiple Ten Gigabit Ethernet ports simultaneously.
Command to add a description string to an Ethernet port.
Command to disable an Ethernet port.
Command to enable the flow-control function for a port to avoid packet loss.
Command to configure the Duplex Mode (auto, full, half) for an Ethernet port.
Command to configure the Speed Mode (10/100/1000/10000/auto) for an Ethernet port.
Command to enable broadcast storm control by filtering broadcast packets.
Command to enable multicast storm control by filtering multicast packets.
Command to enable unicast storm control by filtering UL frames.
Command to configure the bandwidth limit (ingress/egress) for Ethernet ports.
Command to clear the statistic information of all Ethernet ports.
Command to display the connective-status of Ethernet ports.
Command to display the statistic information of an Ethernet port.
Command to display Ethernet port configurations (status, flow control, etc.).
Command to display storm-control information for Ethernet ports.
Command to display bandwidth-limit information for Ethernet ports.
Command to configure CoS (Class of Service) priority for ports.
Command to map DSCP Priority to TC egress queue.
Command to map 802.1P/802.1Q tags, CoS, and TC egress queues.
Command to map DSCP Priority to TC egress queue.
Command to configure the queue scheduling mode (SP, WRR, SP+WRR, EQU).
Command to display QoS configuration based on port priority.
Command to display 802.1P Priority and CoS-ID to TC-ID mapping.
Command to display DSCP Priority configuration.
Command to display the schedule rule of egress queues.
Command to display the status of IEEE 802.1P priority and DSCP priority.
Command to configure the monitoring port for a specific monitor session.
Command to configure the monitored ports for a specific monitor session.
Command to display the configuration of port monitoring sessions.
Command to configure the forward port list for a port to restrict traffic flow.
Command to display the forward port list of a port.
Command to add Time-Ranges for ACLs to control access based on time.
Command to configure a time-range into absolute mode with start and end dates.
Command to configure time-ranges into periodic mode based on week-day and time-slice.
Command to configure time-ranges into Holiday Mode.
Command to define a global holiday with start and end dates.
Command to create standard-IP ACLs and extend-IP ACLs.
Command to create MAC ACLs for filtering based on MAC addresses.
Command to add rules to Standard-IP ACLs based on IP addresses.
Command to add rules to Extended-IP ACLs with detailed matching conditions.
Command to configure MAC ACL rules, including permit/deny actions.
Command to add a Policy to group ACLs and define actions.
Command to add ACLs and create actions for a policy.
Command to configure the direction function of policy action for specified ports.
Command to configure Stream Condition function of policy action (rate, OSD).
Command to configure Stream Mirror function of policy action.
Command to configure QoS remarking function of policy action (DSCP, priority).
Command to bind a policy to a specified port.
Command to bind a policy to a VLAN.
Command to display the configuration of time-ranges.
Command to display the defined holidays.
Command to display configuration of ACLs.
Command to display information of a specified policy.
Command to display the configuration of policy bindings.
Command to enable the STP function globally.
Command to enable STP function for a specified port.
Command to configure common parameters for ports in MST instances.
Command to configure the STP mode (STP, RSTP, MSTP).
Command to access MST Configuration Mode for VLAN-Instance mapping.
Command to configure VLAN-Instance mapping or disable instances.
Command to configure the region name of MST instance.
Command to configure the revision level of MST instance.
Command to configure the priority of MST instances.
Command to configure MST Instance Port parameters and view port status.
Command to configure the bridge priority for Spanning Tree.
Command to configure TC Protect globally to handle continuous TC-BPDUs.
Command to configure Spanning Tree timers (forward-time, hello-time, max-age).
Command to configure the maximum BPDU packets transmitted per Hello Time interval.
Command to configure the maximum hops before BPDU is discarded.
Command to enable BPDU filter function on a port.
Command to enable BPDU protect function for a port.
Command to enable Loop Protect function for a port to prevent network loops.
Command to enable Root Protect function for a port.
Command to enable TC Protect function for a port.
Command to enable MCheck function for a port.
Command to display the active information of spanning-tree.
Command to display the bridge parameters of spanning-tree.
Command to display spanning-tree information for ports.
Command to display protect information of ports for spanning-tree.
Command to display related information of MST instances.
Command to configure IGMP Snooping globally.
Command to enable IGMP Snooping function for a desired port.
Command to configure the Fast Leave function for ports.
Command to process unknown multicast as 'discard'.
Command to enable VLAN IGMP Snooping or create static multicast IP entries.
Command to configure the maximum number of groups a port can join.
Command to create and configure a Multicast VLAN.
Command to enable IGMP Snooping Querier function for VLANs.
Command to configure parameters for IGMP Snooping Querier general query frames.
Command to configure parameters for IGMP Snooping Querier specific query frames.
Command to display the global configuration of IGMP Snooping.
Command to display the port configuration of IGMP.
Command to display the VLAN configuration of IGMP Snooping.
Command to display the Multicast VLAN configuration.
Command to display information of all IGMP snooping groups.
Command to display IGMP Snooping Querier configurations for specified VLANs.
Command to enable the SNMP function for network device management.
Command to add SNMP Views for managing MIB objects.
Command to manage and configure SNMP groups for device access control.
Command to add SNMP users and manage their access rights.
Command to add SNMP communities for authentication and access control.
Command to add notification hosts for SNMP traps and informs.
Command to configure local and remote SNMP engine IDs.
Command to enable standard SNMP traps (linkup, linkdown, warmstart, coldstart).
Command to enable SNMP link status traps for specified ports.
Command to enable SNMP extended traps (CPU, flash, storm-control, etc.).
Command to enable SNMP extended MAC address-related traps.
Command to enable SNMP extended VLAN-related traps (create, delete).
Command to configure RMON history sample entries for network monitoring.
Command to configure SNMP-RMON Event entries for alarms.
Command to configure SNMP-RMON Alarm Management for monitoring variables.
Command to configure SNMP-RMON statistics entries.
Command to display SNMP configuration globally.
Command to display the View table.
Command to display the Group table.
Command to display the User table.
Command to display the Community table.
Command to display the Host table.
Command to display the engineID of the SNMP.
Command to display the configuration of RMON history sample entries.
Command to display the configuration of SNMP-RMON Event.
Command to display the configuration of the Alarm Management entry.
Command to display the configuration of the specified statistics entry.
Command to enable the LLDP function for advertising device information.
Command to configure the Hold Multiplier parameter for LLDP aging time.
Command to configure LLDP transmission parameters (tx-interval, tx-delay, etc.).
Command to enable a port to receive LLDPDUs.
Command to enable a port to transmit LLDPDUs.
Command to enable SNMP notification for LLDP events on ports.
Command to configure which TLVs are included in outgoing LLDPDUs.
Command to configure the number of LLDP-MED frames sent during fast start.
Command to enable LLDP-MED feature for ports, changing Admin Status to Tx&Rx.
Command to configure LLDP-MED TLVs to be included in outgoing LLDPDUs.
Command to configure Location Identification TLV content in outgoing LLDPDUs.
Command to display the global configuration of LLDP.
Command to display LLDP configuration for specified or all ports.
Command to display LLDP information of corresponding ports.
Command to display neighbor information of corresponding ports.
Command to display LLDP statistic information between local and neighbor devices.
Command to configure NDP (Neighbor Discovery Protocol) globally for cluster management.
Command to configure NTDP (Neighbor Topology Discovery Protocol) globally for cluster management.
Command to manually collect topology information for cluster management.
Command to configure cluster functions for a specified port.
Command to create a new cluster and configure its IP address pool.
Command to specify the cluster name before cluster creation.
Command to configure cluster hold time and handshake packet interval.
Command to add or delete member switches to the cluster using MAC address.
Command to specify the current switch as a candidate switch for cluster.
Command to specify the current switch as an individual switch.
Command to specify the VLAN used for managing clusters.
Command to clear NDP message statistics on specified ports.
Command to display the NDP information of the switch.
Command to display the cluster's neighbor information.
Command to display NTDP configuration information.
Command to display the global configuration of the Cluster (when Commander Switch).
Command to display the member information of the cluster.
Command to create a VLAN interface for routing.
Command to create a loopback interface for routing.
Command to switch Layer 3 interfaces to Layer 2 ports, or vice versa.
Command to shut down (disable) a specified interface.
Command to add a description to a Layer 3 interface.
Command to configure static routes with destination, mask, and next-hop.
Command to enable the Layer 3 routing function.
Command to display information about specified loopback interfaces.
Command to display information for a specified interface VLAN.
Command to display detailed information of specified Layer 3 interfaces.
Command to display summary information of Layer 3 interfaces.
Command to display IP route entries of a specified type (static, connected, RIP, OSPF).
Command to display invalid routing information for specified IP addresses or networks.
Command to display a summary of route entries classified by their sources.
Command to enable DHCP service globally, including Server and Relay functions.
Command to specify reserved IP addresses forbidden for allocation.
Command to create an address pool for DHCP Server and enter DHCP configuration mode.
Command to specify the timeout value for the PING process.
Command to specify the number of PING packets sent; 0 disables PING.
Command to specify the address and subnet of the network pool.
Command to specify the lease time for addresses in the address pool.
Command to reserve static addresses bound with hardware (MAC) addresses.
Command to specify static addresses bound with client identifiers.
Command to specify the default gateway list for the address pool.
Command to specify the DNS server list for the address pool.
Command to display the status of the DHCP service.
Command to display statistics of DHCP packets.
Command to display the configuration of the address pool.
Command to display the configuration of reserved addresses.
Command to display the configuration of static binding addresses.
Command to display the binding entries.
Command to clear the statistics information of DHCP packets.
Command to clear the binding information.
Command to add DHCP Server address to a Layer 3 interface.
Command to enable Option 82 support in DHCP Relay.
Command to specify the policy for receiving DHCP request packets with Option 82.
Command to enable Option 82 customization function.
Command to specify the custom circuit ID for DHCP Option 82 customization.
Command to specify the custom remote ID for DHCP Option 82 customization.
Command to display the configuration of DHCP Relay.
Command to enable Proxy ARP function on specified VLAN interface or routed port.
Command to display the Proxy ARP status.
Command to enable IGMP function on a specified interface.
Command to configure the version of IGMP (1, 2, or 3) on specified interface.
Command to configure the number of Specific Query Messages sent by the switch.
Command to configure the interval for Specific Query Messages sent by the switch.
Command to configure the existing time of non-queriers on specified interfaces.
Command to configure the interval of General Query Messages sent by the switch.
Command to specify the max response time to General Query messages.
Command to check the router-alert option of IGMP messages on specified interfaces.
Command to configure the robustness value of IGMP.
Command to configure sending IGMP messages to carry the router-alert option.
Command to configure the interval of Startup Query Messages sent by the switch.
Command to configure the number of Startup Query Messages sent by the switch.
Command to configure static multicast groups on specified interface VLANs.
Command to configure static multicast groups on specified routed ports.
Command to create an IGMP configuration profile.
Command to configure the filtering mode of a profile as deny.
Command to configure the filtering mode of a profile as permit.
Command to configure the range of a profile's filtering multicast address.
Command to bind a profile to a specified Ethernet port or routed port.
Command to configure the maximum number of groups a port can join.
Command to display the configuration information of IGMP profiles.
Command to display information of all dynamic multicast groups.
Command to display information of dynamic multicast groups on specified ports.
Command to display information of dynamic multicast groups on specified VLANs.
Command to display information of all static multicast groups.
Command to display information of static multicast groups on specified ports.
Command to display static multicast groups on specified Interface VLANs.
Command to display information of layer 2 forwarding ports for dynamic multicast groups.
Command to display IGMP configuration information on specified ports.
Command to display IGMP configuration information on specified VLANs.
Command to display IGMP configuration information on specified loopback interfaces.
Command to enable IP multicast routing function globally.
Command to enable PIM function on a specified interface (dense or sparse mode).
Command to specify the expiry time for routing entries.
Command to configure sources to use the shared tree, not switching to source tree.
Command to configure the candidate BSR on a specified interface.
Command to configure the candidate RP on a specific interface.
Command to configure the static RP address.
Command to configure the border of BSR packets on interfaces connecting to PIM domains.
Command to configure the priority of the Designated Router (DR).
Command to configure the interval for join/prune packets.
Command to configure the interval of Hello packets.
Command to display IP multicast information.
Command to display the IP multicast routing table.
Command to display the specified PIM interface information.
Command to display PIM neighbor information.
Command to display candidate BSR and RP information.
Command to display the RP information of the specified multicast group.
Command to display the hash result of a specified multicast group.
Command to add or modify static multicast routing entries.
Command to display all static multicast routing entries.
Command to enable VRRP protocol on an interface and designate a virtual router ID.
Command to add a virtual IP address for the virtual router.
Command to configure or modify the description for the virtual router.
Command to set the priority value for the virtual router configured on an interface.
Command to set the frequency for sending virtual router advertisements.
Command to set preemption mode and delay time for virtual routers.
Command to set the authorization detail value for virtual routers (simple or MD5).
Command to add tracked interfaces for the virtual router.
Command to clear all VRRP statistics on the switch.
Command to display basic configuration information of virtual routers.
Command to display statistics of a virtual router on an interface.
Command to enable the RIP function and enter router configuration mode.
Command to enable RIP function on interfaces of a desired network.
Command to specify the RIP version (v1 or v2) globally.
Command to configure RIP protocol timers (update, timeout, garbage-collect).
Command to configure the administrative distance for RIP routes.
Command to enable Auto Summary mode for RIPv2.
Command to configure the default metric of redistributed routes.
Command to redistribute external routes from other protocols into OSPF.
Command to prevent an interface from sending OSPF update messages.
Command to specify the RIP receive version on interfaces.
Command to specify the RIP send version on interfaces.
Command to configure interface to send RIPv2 packets via broadcast.
Command to configure the authentication mode for RIP on interfaces.
Command to enable poison reverse function on interfaces.
Command to enable split horizon function on interfaces.
Command to display RIP configurations, interfaces, or routing table.
Command to create an OSPF routing process and enter router configuration mode.
Command to configure the router ID for OSPF processes.
Command to configure the network for a specified OSPF area.
Command to configure a summary route for OSPF ASBRs.
Command to configure the maximum number of equal-cost multipath routings.
Command to redistribute external routes from other protocols into OSPF.
Command to configure the default cost of redistributing external routes.
Command to advertise the default route as AS-External LSA.
Command to enable auto-computing interface cost and set reference bandwidth.
Command to configure the OSPF administrative distance.
Command to configure SPF computing delay and interval to reduce CPU/memory usage.
Command to configure the minimum interval time for the same LSA instances.
Command to configure OSPF compatibility for routing rules in RFC 1583.
Command to prevent an interface from sending OSPF packets.
Command to prevent multiple interfaces from sending OSPF packets.
Command to prevent all interfaces from sending OSPF packets.
Command to delete a specified OSPF area.
Command to configure the area name.
Command to configure the authentication mode for a specified OSPF area.
Command to define an area as a stub area.
Command to define an area as an NSSA area.
Command to configure the cost of default summary routes sent from ABR.
Command to configure a summary route for OSPF areas.
Command to configure virtual-links for OSPF areas.
Command to configure the authentication type for virtual links.
Command to configure the authentication key for simple authentication.
Command to configure MD5 authentication ID and key for virtual links.
Command to configure the interface cost for OSPF.
Command to configure the interval to retransmit LSA, DD, and LSR packets.
Command to configure the transmission delay of LSA on specified interfaces.
Command to configure the priority of the specified interface for OSPF.
Command to configure the hello intervals on specified interfaces.
Command to set the time after which neighbors declare an OSPF router down.
Command to configure the authentication mode for specified OSPF interfaces.
Command to configure the key for simple authentication.
Command to configure the ID and password for MD5 authentication.
Command to configure the network type (broadcast or point-to-point) on specified interface.
Command to block flooding of LSA packets on specified interfaces.
Command to ignore MTU check in DD exchanging process for OSPF.
Command to reset the OSPF process, clearing dynamic information.
Command to display global information of the OSPF process.
Command to display the LSDB and detailed LSA information.
Command to display interface information for OSPF processes.
Command to display information of OSPF neighbors.
Command to display the LSA request list.
Command to display the LSA retransmission list.
Command to display ASBR summary routes.
Command to display the virtual links in OSPF processes.
Command to display routing tables of ABR/ASBR.
Command to display the OSPF routing table.
Command to display the LSDB of a specified OSPF area.
Command to display interface information of a specified OSPF area.
Command to display neighbor information of a specified OSPF area.
Command to display the LSA request list of a specified OSPF area.
Command to display the LSA retransmission list of a specified OSPF area.
To Next Page