Mindray BeneVision TM80

To Next Page

To Previous Page

Using the Pouch Getting Started

3 - 18 TM80 Telemetry Monitor Operator’s Manual

This page intentionally left blank.

Main Page

Default Chapter7
- Table of Contents7
1 Safety15
- Safety Information16
- Equipment Symbols21
2 General Product Description23
- Intended for Use24
- Applied Parts24
- Key Features25
- Components25
- Physical View26
- Touch Screen Display27
  - Display Screen28
  - On-Screen Keyboard30
3 Getting Started33
- Unpacking and Checking35
- Environmental Requirements35
- Connecting the ECG Leadwire36
- Installing the Batteries37
  - Installing the Lithium-Ion Rechargeable Battery Pack38
  - Installing the AA Batteries39
- Powering on the Unit40
- Understanding Touch Gestures41
- Basic Operations41
- Using the Pouch46
  - Securing the Pouch for the TM8047
  - Securing Pouches for the TM80 and BP1049
4 User Configurations51
- Introduction52
- Configuring the Display52
- Configuring the Audio Volume54
5 Patient Management57
- Introduction58
- Admitting a Patient58
- Changing Patient Information58
- Entering the Standby Mode61
- Exiting the Standby Mode61
- Discharging the Patient62
  - Selecting the Discharge Patient Menu62
  - Restarting the TM8062
6 Alarms63
- Introduction64
- Alarm Safety Information64
- Understanding the Alarms65
- Viewing Alarms67
- Changing Alarm Settings68
- Pausing Alarms70
- Resetting Alarms71
  - Resetting Physiological Alarms71
  - Resetting Technical Alarms71
- Latching Alarms72
- Actions When an Alarm Occurs72
7 Monitoring ECG, Arrhythmia, ST and QT73
- Introduction74
- ECG Safety Information74
- Preparation for Monitoring ECG75
- Changing ECG Settings85
- Configuring the HR Alarm Source89
- Understanding the ECG Display90
- Arrhythmia Monitoring92
- ST Segment Monitoring101
- Qt/Qtc Interval Monitoring105
- Relearning107
  - Automatically Initiating an ECG Relearning108
  - Manually Initiating an ECG Relearning108
8 Monitoring Respiration (Resp) (Optional)109
- Introduction110
- Resp Safety Information110
- Preparation for Monitoring Resp111
  - Preparing the Patient's Skin111
  - Positioning the Electrodes111
- Changing Resp Settings112
- Understanding the Resp Display115
9 Monitoring Pulse Oxygen Saturation (Spo2) (Optional)118
- Introduction118
- Measurement Limitations118
- Safety119
- Connecting the Spo2 Module120
- Changing the Spo2 Settings122
- Spo2 Measurement126
  - Identifying Spo2 Modules126
  - Applying the Sensor126
- Understanding the Spo2 Display127
  - Spo2 Digital Area127
  - Spo2 Waveform Area128
- Masimo Information129
- Nellcor Information130
10 Monitoring Noninvasive Blood Pressure (NIBP) (Optional)132
- Pairing Introduction132
- Pairing a TM80 with a BP10132
  - Pairing Procedures132
  - System Responses after Successful Pairing133
- Unpairing the TM80 with the BP10134
- Screen Display after Pairing a TM80 with a BP10136
- Interactions after Pairing a TM80 with a BP10137
11 Review141
- Introduction142
- Tabular Trends Review Page142
- Events Review Page145
12 Configuring the TM80149
- Introduction150
- Entering the Maintenance Menu150
- Configuring the General Menu150
  - Configuring Device Location151
- Configuring the Alarms Menu152
- Quick Keys Menu154
  - Changing the Quick Keys154
  - Deleting a Quick Key155
- Configuring the Network Menu155
- Configuring the Defaults Menu162
  - Transferring a Configuration162
- Screen Lock Menu163
- Changing the Passwords164
- 12.10 Changing the Device Name165
- 12.11 Setting CMS Disconnect Alarm165
- 12.12 Demo Mode166
- 12.13 Service Menu166
- Introduction168
13 Monitoring with the TM80 at the CMS168
- Network Safety Information169
- Adjusting the Minimum QRS Detection Threshold169
- QT Monitoring170
- ST Monitoring173
- Arrhythmia Monitoring177
  - Configuring the PVC-Related Alarm Threshold177
  - Configuring the Arrhythmia Shield Time178
- Locating the TM80179
- Sending a Notification to the TM80179
- 13.10 Triggering an Alarm Reminding Patients' Location180
14 Battery181
- Introduction182
- Safety182
- Installing the Battery184
- Checking the Battery Charge Status184
- Removing the Battery184
- Charging the Rechargeable Lithium-Ion Battery185
- Storing the Batteries186
  - Storing Rechargeable Lithium-Ion Batteries186
  - Storing AA Batteries187
- Maintaining the Rechargeable Lithium-Ion Battery187
- Disposing of the Batteries188
  - Disposing of the Rechargeable Lithium-Ion Battery188
  - Disposing of the AA Batteries188
15 Troubleshooting189
- General Problems190
- Physiological Alarm Messages at the TM80192
- Technical Alarm Messages at the TM80196
16 Cleaning and Disinfecting205
- Introduction206
- Safety Information206
- Cleaning and Disinfecting the Equipment207
- Cleaning and Disinfecting ECG Leadwires and Spo2 Sensors211
- Cleaning and Disinfecting Other Parts212
- Sterilization213
- Impact of Improper Cleaning or Disinfection213
17 Maintenance215
- Introduction216
- Safety216
- Regular Check217
- Maintenance and Testing Schedule218
- Power-On Test218
- Verifying the ECG219
- NIBP Accuracy Test219
- NIBP Leakage Test219
- Nurse Call Test219
- 17.10 Electrical Safety Tests219
- 17.11 Battery Check220
- 17.12 Viewing System Information220
18 Accessories221
- ECG Accessories222
  - ECG Electrodes222
  - ECG Leadsets223
- Spo2 Accessories224
- NIBP Accessories225
- Miscellaneous225
A Product Specifications228
- Classifications228
- Environmental Specifications228
- Power Supply Specifications229
  - Tm80229
  - Central Charger230
- Physical Specifications230
- Hardware Specifications231
  - Tm80231
- Data Storage232
- Wireless Specification232
- Measurement Specifications236
C FCC Compliance253
D Symbols and Abbreviations257
- Units258
- Symbols259
- Abbreviations259

Mindray BeneVision TM80 - Page 50

Table of Contents

Other manuals for Mindray BeneVision TM80

Related product manuals