7B1-122 AUTOMATIC TRANSAXLE (M13 ENGINE)
1. Torque converter 33. Oil pan 65. 2nd brake retaining plate
2. Torque converter housing
: Apply sealant 99000-31230 to mating
surface to transaxle case.
34. A/T fluid drain plug 66. 2nd brake disc
3. Oil strainer assembly
: Replace oil strainer when overhaul-
ing.
35. Manual select lever 67. 2nd brake separator plate
4. Parking lock pawl shaft 36. Lock washer 68. 2nd brake return spring subassembly
5. Parking lock pawl 37. Transmission range sensor 69. Front sun gear thrust bearing race
6. Parking lock pawl return spring 38. Cooler check valve 70. Front planetary sun gear
7. Parking lock pawl rod 39. Spring 71. Planetary gear thrust bearing
8. Parking lock pawl bracket 40. Transaxle case plug 72. One-way clutch No.1 assembly
9. Manual detent spring 41. Fluid filler tube 73. Rear planetary sun gear subassem-
bly
10. Manual valve lever 42. Fluid level gauge 74. Rear sun gear thrust bearing race
11. Manual valve lever pin 43. Fluid cooler inlet pipe 75. Rear sun gear thrust bearing
12. Manual shift shaft 44. Fluid cooler outlet pipe 76. Forward clutch hub
13. Manual shift shaft oil seal
: Apply grease 99000-25030 to oil seal
lip.
45. 2nd brake gasket 77. Intermediate shaft thrust bearing race
14. Differential side oil seal
: Apply grease 99000-25030 to oil seal
lip.
46. Brake drum gasket 78. Intermediate shaft thrust bearing
15. Torque converter housing plug 47. Pipe union 79. 2nd brake piston snap ring
16. Lubrication LH tube 48. Reduction drive gear nut
: After tightening nut so as rota-
tional torque of reduction drive gear
to be in specified value, caulk nut
securely.
80. O/D and 2nd coast brake retaining
plate snap ring
17. Lubrication RH tube 49. Reduction drive gear 81. O/D and 2nd coast brake retaining
plate
18. Fluid reservoir RH plate 50. Planetary ring gear subassembly 82. O/D and 2nd coast brake disc
19. Input shaft front thrust bearing 51. Breather hose 83. O/D and 2nd coast brake separator
plate
20. Input shaft rear thrust bearing 52. Breather union 84. O/D and 2nd coast brake rear plate
21. Input shaft rear thrust bearing race 53. Input shaft speed sensor 85. Rear cover seal ring
22. Direct clutch hub 54. Valve body harness 86. Reverse clutch drum thrust bearing
23. Lubrication tube clamp 55. 1st and reverse brake piston 87. Rear cover plug
24. Fluid reservoir LH plate 56. O-ring 88. Transaxle rear cover
: Apply sealant 99000-31230 to mat-
ing surface.
25. Governor apply No.2 gasket 57. 1st and reverse brake return spring
subassembly
89. Harness bracket
26. Automatic transaxle case 58. 1st and reverse brake disc 90. Select cable clamp
27. Accumulator piston O-ring 59. 1st and reverse brake separator
plate
91. Governor apply No.1 gasket
28. Accumulator spring 60. 1st and reverse brake retaining
plate
92. Output shaft speed sensor (VSS)
29. C2 accumulator piston 61. 1st and reverse brake snap ring 93. One-way clutch outer race retainer
30. C1 accumulator piston 62. Planetary gear assembly Do not reuse.
31. B1 accumulator piston 63. Planetary carrier thrust washer
: Apply grease 99000-25030 to
slide contact face.
Apply automatic transaxle fluid.
32. Oil pan gasket 64. One-way clutch No.2 assembly Tightening torque
To Next Page
Loading...
