Xerox VersaLink B7035 Service Manual

April 2017
4-1
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
Repairs and Adjustments
Launch Issue
4 Repairs and Adjustments
REPs 1 - Standby Power
REP 1.1 HVPS................................................................................................................ 4-5
REP 1.2 Drive PWB ........................................................................................................ 4-6
REP 1.3 LVPS................................................................................................................. 4-8
REP 1.4 LVPS Assembly................................................................................................ 4-9
REPs 2 - User Interface
REP 2.1 User Interface Assembly................................................................................... 4-11
REPs 3 - Machine Run Control
REP 3.1 ESS PWB ......................................................................................................... 4-13
REP 3.2 ESS PWB Chassis Assembly........................................................................... 4-18
REP 3.3 SD Card ............................................................................................................ 4-23
REPs 5 - DADF
REP 5.1 DADF Removal................................................................................................. 4-25
REP 5.2 DADF Document Cushion ................................................................................ 4-27
REP 5.3 DADF Front Cover............................................................................................ 4-28
REP 5.4 DADF Rear Cover............................................................................................. 4-28
REP 5.5 DADF PWB....................................................................................................... 4-30
REP 5.6 Upper Feeder Assembly ................................................................................... 4-31
REP 5.7 DADF Feeder Assembly ................................................................................... 4-32
REP 5.8 Left Counter Balance ........................................................................................ 4-33
REP 5.9 Right Counter Balance...................................................................................... 4-34
REP 5.10 Feed/Nudger Roll Assembly........................................................................... 4-35
REP 5.11 Harness Guide and Wire Harness .................................................................. 4-36
REP 5.12 DADF Feed Motor Assembly.......................................................................... 4-39
REP 5.13 DADF Drive Belt ............................................................................................. 4-40
REP 5.14 Document Tray ............................................................................................... 4-41
REP 5.15 Retard Chute Assembly.................................................................................. 4-42
REP 5.16 Invert Chute Assembly.................................................................................... 4-43
REP 5.17 DADF Takeaway Roll ..................................................................................... 4-43
REP 5.18 Sensor Bracket Assembly............................................................................... 4-47
REP 5.19 Retard Roll Assembly ..................................................................................... 4-48
REPs 10 - Print Transportation and Fusing
REP 10.1 Exit 1 OCT Assembly...................................................................................... 4-49
REP 10.2 Exit 2 Roll........................................................................................................ 4-50
REP 10.3 Fuser Removal ............................................................................................... 4-52
REP 10.4 Fuser Fan Duct Assembly .............................................................................. 4-53
REPs 12 - Integrated Office Finisher
REP 12.1 Integrated Office Finisher Removal ................................................................ 4-55
REP 12.2 Paddle Belts.................................................................................................... 4-56
REP 12.3 Sub Paddle Solenoid ...................................................................................... 4-59
REP 12.4 Stapler Assembly............................................................................................ 4-60
REP 12.5 Set Clamp Home Sensor................................................................................ 4-61
REP 12.6 Exit Roll Assembly.......................................................................................... 4-63
REP 12.7 Nip Roll ........................................................................................................... 4-64
REP 12.8 Finisher Entry Sensor ..................................................................................... 4-64
REP 12.9 Compiler Exit Sensor ...................................................................................... 4-66
REP 12.10 Main Paddle Shaft Assembly........................................................................ 4-67
REP 12.11 Lower Chute Assembly................................................................................. 4-69
REP 12.12 Entry Roll ...................................................................................................... 4-71
REP 12.13 Upper Chute Assembly................................................................................. 4-72
REP 12.14 Finisher PWB................................................................................................ 4-73
REP 12.15 Stacker Tray Assembly................................................................................. 4-74
REP 12.16 Stacker Shaft Assembly................................................................................ 4-75
REP 12.17 Stacker Motor................................................................................................ 4-78
REP 12.18 Stack Sensor 1 and Stack Sensor 2 ............................................................. 4-79
REP 12.19 Compiler Assembly....................................................................................... 4-80
REP 12.20 Set Clamp Shaft............................................................................................ 4-82
REP 12.21 Eject Belt....................................................................................................... 4-83
REP 12.22 Eject/Set Clamp Motor Assembly ................................................................. 4-84
REP 12.23 Rear Tamper Home Sensor.......................................................................... 4-86
REP 12.24 Eject Shaft Assembly.................................................................................... 4-87
REP 12.25 Front /Rear Tamper Motor Assembly............................................................ 4-89
REP 12.26 Front Tamper Home Sensor ......................................................................... 4-90
REP 12.27 Eject Home Sensor....................................................................................... 4-91
REP 12.28 Stack Height Sensor ..................................................................................... 4-93
REPs 13 - Office Finisher LX
REP 13.1 H-Transport Assembly .................................................................................... 4-95
REP 13.2 Hole Punch Assembly..................................................................................... 4-95
REP 13.3 H-Transport Belt.............................................................................................. 4-96
REP 13.4 H-Transport Motor........................................................................................... 4-97
REP 13.5 Finisher LX Undocking.................................................................................... 4-97
REP 13.6 Front Cover..................................................................................................... 4-98
REP 13.7 Rear Upper Cover........................................................................................... 4-99
REP 13.8 Rear Lower Cover........................................................................................... 4-99
REP 13.9 Eject Cover ..................................................................................................... 4-100
REP 13.10 Foot Cover .................................................................................................... 4-102
REP 13.11 Stacker Lower Cover .................................................................................... 4-102
REP 13.12 Stacker Upper Cover .................................................................................... 4-103
REP 13.13 Stack Height Sensors 1 and 2 ...................................................................... 4-103
REP 13.14 Sub Paddle Solenoid Assembly.................................................................... 4-104
REP 13.15 Stapler Move Motor....................................................................................... 4-104
REP 13.16 Finisher Stapler Assembly ............................................................................ 4-106
REP 13.17 Compiler Tray Assembly............................................................................... 4-107
REP 13.18 Crease Assembly.......................................................................................... 4-116
REP 13.19 Stacker Elevator Motor ................................................................................. 4-117
REP 13.20 Stacker Tray.................................................................................................. 4-118
REP 13.21 Eject Belt....................................................................................................... 4-118
REP 13.22 Eject Motor Assembly ................................................................................... 4-119
REP 13.23 Finisher PWB................................................................................................ 4-119
REP 13.24 Finisher LVPS............................................................................................... 4-120
REP 13.25 Eject Motor.................................................................................................... 4-121

Xerox VersaLink B7035 Specifications

General

Duplex printing	Yes
Print technology	LED
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	9.1 s
Print speed (black, normal quality, A4/US Letter)	35 ppm
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	999 copies
Time to first copy (black, normal)	5.4 s
Scan to	E-mail, FTP, SMB, USB
Scanner type	-
Input color depth	24 bit
Faxing	Mono faxing
Modem speed	33.6 Kbit/s
Printing colors	Black
Maximum duty cycle	129000 pages per month
Page description languages	HP-GL, PCL 5e, PCL 6, TIFF, XPS
Internal memory	2048 MB
Processor cores	2
Processor frequency	1050 MHz
Control type	Touch
Product color	Black, White
Display diagonal	7 \
Market positioning	Business
Cabling technology	10/100/1000Base-T(X)
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Mobile printing technologies	Apple AirPrint, Google Cloud Print
Standard interfaces	Ethernet, NFC, USB 3.2 Gen 1 (3.1 Gen 1)
Optional connectivity	Wireless LAN
USB 3.2 Gen 1 (3.1 Gen 1) ports quantity	1
Power consumption (average operating)	- W
Mac operating systems supported	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Y
Linux operating systems supported	Fedora 24, openSUSE 13.2
Other operating systems supported	IBM AIX 7.2
Server operating systems supported	Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012
Windows operating systems supported	Windows 10, Windows 10 Education, Windows 10 Education x64, Windows 10 Enterprise, Windows 10 Enterprise x64, Windows 10 Home, Windows 10 Home x64, Windows 10 Pro, Windows 10 Pro x64, Windows 7 Enterprise, Windows 7 Enterprise x64, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional x64, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Pro x64, Windows 8 x64
Sustainability certificates	ENERGY STAR
Total input capacity	- sheets
Paper tray media types	Bond paper, Card stock, Envelopes, Heavy paper, Labels, Letterhead, Plain paper, Pre-Printed, Recycled paper
ISO A-series sizes (A0...A9)	A3, A4
Maximum ISO A-series paper size	A3

Weight and Dimensions

Depth	670.8 mm
Width	590 mm
Height	767.9 mm
Weight	- g