Chapter 22 Virtual Servers
ZyWALL Series CLI Reference Guide
193
Note: If you create a NAT rule using the IP address of the Web Configurator and set the
external port to 80 or 443, the rule will conflict with the Zyxel Device’s default HTTP server
port. You will not be able to access the Web Configurator through this interface..
Table 99 ip virtual-server Commands
COMMAND DESCRIPTION
show ip virtual-server
[profile_name]
Displays information about the specified virtual server or about all the virtual
servers.
no ip virtual-server profile_name
Deletes the specified virtual server.
ip virtual-server profile_name
interface interface_name source-
ip {any | IPv4 | address-object}
original-ip {any | ip |
address_object} map-to
{address_object | ip} map-type
any [nat-loopback [nat-1-1-map]
[deactivate] | nat-1-1-map
[deactivate] | deactivate]
Creates or modifies the specified virtual server and maps the specified
destination IP address (for all destination ports) to the specified destination
address object or IP address. The original destination IP is defined by the specified
interface (any), the specified IP address (IP), or the specified address object
(address-object). NAT loopback allows local users to use a domain name to
access this virtual server.
The source IP is the source IP address of the incoming packets.
The original destination IP is defined by the specified interface (any), the
specified IP address (IP), or the specified address object (address-object). NAT
loopback allows local users to use a domain name to access this virtual server.
Select what kind of NAT this rule is to perform.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See Section
22.1.1 on page 192 for more information.
Using this command without nat-1-1-map means the NAT type is Virtual Server.
This makes computers on a private network behind the Zyxel Device available to
a public network outside the Zyxel Device (like the Internet).
The deactivate command disables the virtual server rule.
ip virtual-server profile_name
interface interface_name
original-ip {any | IP |
address_object} map-to
{address_object | ip} map-type
port protocol {any | tcp | udp}
original-port <1..65535> mapped-
port <1..65535> [nat-loopback
[nat-1-1-map] [deactivate] | nat-
1-1-map [deactivate] |
deactivate]
Creates or modifies the specified virtual server and maps the specified
(destination IP address, protocol, and destination port) to the specified
(destination IP address and destination port). The original destination IP is defined
by the specified interface (any), the specified IP address (IP), or the specified
address object (address-object). NAT loopback allows local users to use a
domain name to access this virtual server.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See Section
22.1.1 on page 192 for more information.
Using this command without nat-1-1-map means the NAT type is Virtual Server.
This makes computers on a private network behind the Zyxel Device available to
a public network outside the Zyxel Device (like the Internet).
The deactivate command disables the virtual server rule.
ip virtual-server profile_name
interface interface_name
original-ip {any | IP |
address_object} map-to
{address_object | ip} map-type
ports protocol {any | tcp | udp}
original-port-begin <1..65535>
original-port-end <1..65535>
mapped-port-begin <1..65535>
[nat-loopback [nat-1-1-map]
[deactivate] | nat-1-1-map
[deactivate] | deactivate]
Creates or modifies the specified virtual server and maps the specified
(destination IP address, protocol, and range of destination ports) to the specified
(destination IP address and range of destination ports). The original destination IP
is defined by the specified interface (any), the specified IP address (IP), or the
specified address object (address-object). NAT loopback allows local users to
use a domain name to access this virtual server.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See Section
22.1.1 on page 192 for more information.
Using this command without nat-1-1-map means the NAT type is Virtual Server.
This makes computers on a private network behind the Zyxel Device available to
a public network outside the Zyxel Device (like the Internet).
The deactivate command disables the virtual server rule.
To Next Page
Loading...
