Chapter 64 System Remote Management
ZyWALL Series CLI Reference Guide
537
64.8.3 SNMP Commands
The following table describes the commands available for SNMP. You must use the configure
terminal
command to enter the configuration mode before you can use these commands.
vpnTunnelDisconnect
ed
1.3.6.1.4.1.890.1.6.22
.2.3
This trap is sent when an IPSec VPN tunnel is disconnected.
vpnTunnelName 1.3.6.1.4.1.890.1.6.22
.2.2.1.1
This trap is sent along with the vpnTunnelDisconnected trap. This trap
carries the disconnected tunnel’s IPSec SA name.
vpnIKEName 1.3.6.1.4.1.890.1.6.22
.2.2.1.2
This trap is sent along with the vpnTunnelDisconnected trap. This trap
carries the disconnected tunnel’s IKE SA name.
vpnTunnelSPI 1.3.6.1.4.1.890.1.6.22
.2.2.1.3
This trap is sent along with the vpnTunnelDisconnected trap. This trap
carries the security parameter index (SPI) of the disconnected VPN
tunnel.
Table 310 SNMP Traps (continued)
OBJECT LABEL OBJECT ID DESCRIPTION
Table 311 Command Summary: SNMP
COMMAND DESCRIPTION
[no] snmp-server
Allows SNMP access to the Zyxel Device. The no command
disables SNMP access to the Zyxel Device.
[no] snmp-server
community
community_string
{ro|rw}
Enters up to 64 characters to set the password for read-only (ro) or
read-write (rw) access. The
no command resets the password for
read-only (
ro) or read-write (rw) access to the default.
[no] snmp-server
contact description
Sets the contact information (of up to 60 characters) for the person
in charge of the Zyxel Device. The
no command removes the
contact information for the person in charge of the Zyxel Device.
[no] snmp-server enable
{informs|traps}
Enables all SNMP notifications (informs or traps). The no command
disables all SNMP notifications (informs or traps).
[no] snmp-server host
{w.x.y.z|fqdn|ipv6
address}
[community_string]
Sets the IPv4 or IPv6 address of the host that receives the SNMP
notifications. The
no command removes the host that receives the
SNMP notifications.
[no] snmp-server
location description
Sets the geographic location (of up to 60 characters) for the Zyxel
Device. The
no command removes the geographic location for
the Zyxel Device.
[no] snmp-server port
<1..65535>
Sets the SNMP service port number. The no command resets the
SNMP service port number to the factory default (
161).
snmp-server rule
{rule_number|append|ins
ert rule_number}
access-group
{ALL|address_object}
zone {ALL|zone_object}
action {accept|deny}
Sets a service control rule for SNMP service.
address_object: The name of the IP address (group) object. You
may use 1-31 alphanumeric characters, underscores(
_), or dashes
(-), but the first character cannot be a number. This value is case-
sensitive.
zone_object: The name of the zone. For some Zyxel Device
models, use up to 31 characters (a-zA-Z0-9_-). The name cannot
start with a number. This value is case-sensitive.
For other Zyxel Device models, use pre-defined zone names like
DMZ, LAN1, SSL VPN, IPSec VPN, OPT, and WAN.
To Next Page
Loading...
