GE Vivid S5 N - 5-4-3-2 VGA Interface; 5-4-3-3 CardBus Interface; 5-4-4 Hard Disk

GE
P
ART NUMBER FN091065, REVISION 2 VS5 N AND VS6 N SERVICE MANUAL
5-26 Section 5-4 - Back End Processor
PRELIMINARY
5-4-3 ETX Base Board (cont’d)
The Docking port, located on the rear panel of the ETX Base Board, provides the connections to the
Audio unit on the DIB, discrete control and status lines and 20V-DC power.
Refer to Figure 5-24 "Connectors on the BEP" on page 5-29 for a view of the ETX Base Board showing
the location of the various connectors.
Figure 5-21 "ETX Base Board - Block Diagram" on page 5-26 shows a block diagram of the high level
functions of the ETX Base Board.
Figure 5-21 ETX Base Board - Block Diagram
5-4-3-2 VGA Interface
The interface to the VGA is via the VGA connector on the rear side of the ETX Base Board. The VGA
port is connected to the DIB where VGA signals are converted to DVI and split into three channels to
drive the system LCD display (15" or 17", as applicable), external monitor and DVR.
5-4-3-3 CardBus Interface
Not in use.
5-4-4 Hard Disk
The Hard Disk is the main storage device of the Vivid S5 N or Vivid S6 N ultrasound unit. The Hard Disk,
which is controlled by the CPU via signals from the IDE Bus, is partitioned into four drives, each of which
is designated for different operations, as follows:
• C: Drive: Execution of the operating system and the software application, and factory presets.
The partition size is 2 GB.
• D: Drive: User presets and data. The partition size is 2GB.
J6
RFI
PMC
- MCU
- Battery Conditioning
- DC/DC (+5V_STB to 3.3V)
- PCI Clock detection
P1P3
CardBus
Controller
& Power I/F
Switch
Docking - J18
Power Supply
Unit
J6
PS/2 Bus (x2)
Security
Key
J5
USB
J7
J9
Micro
phone
Audio
Mixer &
Amp
Speakers
J16
PCI Bus
Ext. Speakers
P4
Ethernet
J13
Doppler Audio
J14
IDE Bus
LCD Panel
Keyboard Module
VGA
Monitor
Internal
Speakers
CardBus
I/F
HDD
(IDE) I/F
Docking Mode [0:1]
PCI
Clcok
PWRBTN
LID
PWGIN
PS_ON
RTC
Battery
BATT
SMBus
Ext. DC
EN_BE_PS
PWGIN
EXT_POWER
EXT DC
LOW
PS_SYNCH
Temp. &
Voltage
Monitoring
FAN Control
SMBus
LEDS
Power & LID
Buttons &
de-bouncing
J11 & J12
FANs
EN_FE_PS
+5V_STB
+5V_BE
+12V_BE
+12V
+5V_BE
+5V_BE
+5V_BE
USB
OVCR
+5V_BE
+3.3V
+3.3V_BE
+5V_BE
+3.3V_BE
+12V_BE
+3.3V
PCI
Bus
Switch
EN_FE_PCI
For
Bluetooth
module
Battery
J15
Battery
I/F
Battery
J19
Ext. DC
I/F
Ext. DC
Mech.
protection
for
insertion of
both
sources
J17
I2C Bus
TXPS_EN
Battery
USB x 4
USB
ID
Device
I2C
SMBus
LCD
JILI
I/F
Panel Connector
Internal Connector
DC/DC+5V_BE
+5V_STB
FE_PS_OK
J8
J20
External
Speakers
J10
DOCK
HOT
INS. CTRL
+5V_BE
+5V_DOCK
MUTE
MUTE_DOPPLER
+5V_BE
Created: 13/06/02
Last Edit: 15/01/03
File: BB BD Rev03.vsd
I2C
TXD1/RXD1
TXD1/RXD1
Temp.
Sensors
EXT_DC_LOW
3.3V_BE
12v_BE
Ethernet
Transformer
JX
Ethernet
SW
BAT_SMB_CTRL
SW + PU
ETX_SMB_CTRL