Hurco winmax - Page 290

XII - Index v546CO WinMax Lathe Conversational Part Programming
2 - 123
icons -viii
ID Straight thread 2-40
ID Straight Thread Type 2-45
ID Taper thread 2-40
ID Taper Thread Type 2-47
IN/TAN (INSIDE TANGENT) field
Axial Mill Circle screen 2-148
Axial Mill Frame screen 2 - 154
Cutter Compensation 2 - 189
Radial Mill Circle screen 2-90
Radial Mill Frame screen 2-96
inch per minute (IPM) 1-3
inch per revolution (IPR) 1-3
INCLUDE ARC field
Axial Mill Slot screen
Polar Coordinates 2 - 164
Rectangular Coordinates 2-166
Radial Slot screen
Linear Coordinates 2-108
Rotary Coordinates 2 - 106
infeed angle
Face 2-49
ID Straight 2-46
ID Taper 2-48
OD Straight 2-42
OD Taper 2-44
INSCRIBE field
Axial Mill Flats screen
Polar Coordinates 2 - 171
Rectangular Coordinates 2-173
INSERT BLOCK BEFORE F7 softkey 1-11
insert blocks 1-11
Insert console key
use with Program Review screen 1-9
INSERT ELEMENT BEFORE F7 2-25
INSERT Hole OPERATION F7 softkey
Axial Holes screen 2-178
Radial Holes screen 2-114
INSERT LOCATION BEFORE F7 softkey
Axial Holes Locations screen 2-182
Radial Holes Locations screen 2-121
INSERT TIP RADIUS field
Cutoff block 2-63
Grooving 2-52
Profile Start screen 2-12
Threading 2-38
INSIDE field
Axial Mill Circle screen 2-148
Axial Mill Frame screen 2 - 154
Cutter Compensation 2 - 189
Radial Mill Circle screen 2-90
Radial Mill Frame screen 2-96
INWARD field
Axial Mill Circle scree 2-149
Axial Mill Contour screen 2 - 130
Axial Mill Frame screen 2-155
Radial Mill Circle screen 2-91
Radial Mill Contour screen 2-73
Radial Mill Frame screen 2-97
IPM field
Cutoff block 2-64
IPR field
Cutoff block 2-64
K
keyboard 1-7
L
LEAD (TPI) field
Threading 2-42, 2-44, 2-46, 2-48,
2-49
LEAD IN ANGLE field 2-42, 2-44, 2-46,
2-48, 2-49
LEAD OUT ANGLE field
Threading 2-42, 2-44, 2-46, 2-48,
2-50
LEFT field
Axial Mill Contour screen 2 - 129
Cutter Compensation 2-189
Radial Mill Contour screen 2-72
LENGTH field
Axial Mill Contour Line Segment screen
Rectangular Coordinates 2-137
Face Element screen 2-29
Radial Mill Contour Line Segment
screen
Linear Coordinates 2-80
Taper Element screen 2-31
Turn Element screen 2-28
LINE F1 softkey
Axial Mill Contour screen 2 - 136
New Radial Contour Segment screen 2-
78
Radial Mill Contour Line Segment
screen 2-79
LINE field
Axial Mill Slot screen
Polar Coordinates 2 - 164
Rectangular Coordinates 2-166
Radial Slot screen
Linear Coordinates 2-108
Rotary Coordinates 2 - 106
Line segment
Axial Mill Contour screen 2 - 136
New Radial Contour Segment screen 2-
79
Linear coordinates 2-76, 2-93, 2-100,