Hurco winmax - Index

WinMax Lathe Conversational Part Programming v546CO Index — V
INDEX
Numerics
1) Synchronize Spindles field
Transfer block screen 2 - 207
1ST PECK OFFSET field
Axial Mill Circle screen 2-149
Axial Mill Contour screen 2 - 130
Axial Mill Frame screen 2-156
Radial Mill Circle screen 2-92
Radial Mill Contour screen 2-73
Radial Mill Frame screen 2-98
2) Open Sub-spindle Chuck Dwell (Secs)
field
Transfer block screen 2 - 208
3) Rapid to W Position field
Transfer block screen 2 - 208
4) Feed to W Position field
Transfer block screen 2 - 208
5) Close Sub-spindle Chuck Dwell (Secs)
field
Transfer block screen 2 - 208
6) Open Main Spindle Chuck field
Transfer block screen 2 - 209
7) Move to W Position field
Transfer block screen 2 - 209
8) Close Main Spindle Chuck Dwell (Secs)
field
Transfer block screen 2 - 209
A
ACTIVE OFFSET field
Change Part Setup 2 - 196
ADD LOCATION F5 softkey
Axial Holes Locations screen 2 - 182
Radial Holes Locations screen 2-121
ADDITIONAL AXIS OFFSETS F3 softkey
Change Part Setup 2 - 197
ADVANCE AT X (DIA) or (RAD)
Cutoff block 2-63
ADVANCE PART CATCHER
Cutoff block 2-63
Advanced Pecking tab, Cutoff Block screen
2-65
ALL FACES FIRST turn finish strategy 2-18
ALONG PROFILE turn finish strategy 2-18
angle 2-48
infeed angle ID Straight 2-46
infeed Face 2-49
infeed ID Taper 2-48
infeed OD Straight 2-42
pullout Face 2-50
pullout ID Straight 2-46
pullout OD Straight 2-42
unknown 2-82, 2 - 139
ANGLE field
Axial Mill Contour Line Segment screen
Rectangular Coordinates 2-137
Chamfer Element screen 2-37
Face Element screen 2-29
Radial Mill Contour Line Segment screen
Linear Coordinates 2-80
Taper Element screen 2-31
Turn Element screen 2-28
APPEND ARC field
Axial Mill Slot screen
Polar Coordinates 2 - 164
Rectangular Coordinates 2-166
Radial Slot screen
Linear Coordinates 2-108
Rotary Coordinates 2 - 106
APPROACH ANGLE field
Profile Start screen 2-19
APPROACH CLEARANCE field
Profile Start screen 2-16, 2-19
Arc 2-26
clockwise 2-85, 2-142
element 2-32
segment 2 - 140
ARC F2 softkey
Axial Mill Contour Segment screen 2-
140
New Radial Contour Segment screen 2-
78
Radial Mill Contour Arc Segment screen
2-83
ARC F4 softkey, element 2-26
ARGUMENT TYPE field, NC Program Call
screen 2-211
arguments, NC Program Call screen 2-210
AT END (DIA) or (RAD) field
Axial Mill Slot screen
Polar Coordinates 2 - 165
Rectangular Coordinates 2-167
Radial Slot screen
Linear Coordinates 2-109
Rotary Coordinates 2 - 107
AT START (DIA) or (RAD) field
Axial Mill Slot screen
Polar Coordinates 2 - 165
Rectangular Coordinates 2-167
Radial Slot screen
Linear Coordinates 2-109
Rotary Coordinates 2 - 107
AT-keyboard option 1-7
automatic calculations 1-6, 1-8