Hurco winmax - Page 289

WinMax Lathe Conversational Part Programming v546CO Index — XI
FINAL PECK DEPTH field
Axial Holes Drill Operation screen 2-
180
Radial Holes Drill Operation screen 2-
119
FIND ANOTHER CENTER POINT F7 softkey
2-32
FIND ANOTHER END POINT F7 softkey 2-
31, 2-32
FINISH (1 PASS) field
Axial Mill Flats screen 2 - 168
FINISH (1 PASS), Groove 2-53
FINISH FEED (IPR ) or (MMPR) field
Arc Element screen 2-33
Blend Arc Element screen 2-35
Chamfer Element screen 2-37
Face Element screen 2-30
Taper Element screen 2-31
Turn Element screen 2-28
FINISH OFFSETS field
Arc Element screen 2-33
Blend Arc Element screen 2-35
Chamfer Element screen 2-37
Face Element screen 2-30
Taper Element screen 2-31
Turn Element screen 2-29
FINISH ONLY field
Axial Mill Circle screen 2-147
Axial Mill Contour screen 2 - 128
Axial Mill Flats screen 2 - 168
Axial Mill Frame screen 2-154
Axial Mill Slot screen 2 - 161
Groove 2-53
Radial Mill Circle screen 2-90
Radial Mill Contour screen 2-71
Radial Mill Frame screen 2-96
Radial Slot screen 2-103
FINISH PASSES field
Threading 2-39
Finish Profile data block 2-13
FINISH SPEED (FPM) or (MPM) field
Arc Element screen 2-33
Blend Arc Element screen 2-35
Chamfer Element screen 2-37
Face Element screen 2-30
Taper Element screen 2-31
Turn Element screen 2-28
Finish Speed and Finish Feed values change
to 0 2-14
FIRST PECK DEPTH field
Hole cycle 2-60
FIRST X THEN Y THEN Z F4 softkey 2-9
FIRST X THEN Z F1 softkey 2-8
FIRST Y THEN X THEN Z F6 softkey 2-9
FIRST Y THEN Z THEN X F7 softkey 2-9
FIRST Z THEN X F2 softkey 2-8
FIRST Z THEN Y THEN X F5 softkey 2-9
FLOOR ALLOWANCE field
Axial Mill Circle screen 2-149
Axial Mill Contour screen 2 - 130
Axial Mill Flats screen 2 - 169
Axial Mill Frame screen 2-155
Axial Mill Slot screen 2 - 161
Radial Mill Circle screen 2-91
Radial Mill Contour screen 2-73
Radial Mill Frame screen 2-97
Radial Slot screen 2-103
G
GOUGE AVOIDANCE field
Profile Start screen 2-13
Groove description 1-4
GROOVE F3 softkey 2-52
GROOVE FINISH F4 softkey, Profile screen
2-13
GROOVE ROUGH F3 softkey, Profile screen
2-13
Groove Rough operation rule 2-20
Groove walls 2-56
GROOVE WIDTH field, Grooving 2-54
Groove, roughing and finish pass strategy
2-53
Grooving Cycle 2-51
screen 2-52
H
HEIGHT field
Axial Lettering screen 2-176
Radial Lettering screen 2-111
Hole Cycle screen 2-58
Hole description 1-4
Hole F4 softkey 2-58
Home console key
use with Program Review screen 1-9
home position 2-4
I
I PLANE field
Axial Bolt Circle screen
Polar Coordinate 2-185
Rectangular Coordinates 2-186
Axial Locations screen
Polar Coordinates 2 - 183
Rectangular Coordinates 2-184
Radial Holes Locations screen
Linear Coordinates 2-122
Rotary Coordinates 2 - 122
Radial Holes Loop Around C-Axis screen