MacDon FlexDraper FD140 - Page 16

214683 xiv Revision A
Calibrating the Auto Header Height Control (Gleaner R65/R66/R75/R76 and Pre-2016
S Series) ...................................................................................................................177
Turning off the Accumulator (Gleaner R65/R66/R75/R76 and Pre-2016 S Series) .......................178
Adjusting the Header Raise/Lower Rate (Gleaner R65/R66/R75/R76 and Pre-2016
S Series) ...................................................................................................................179
Adjusting Ground Pressure (Gleaner R65/R66/R75/R76 and Pre-2016 S Series) ........................179
Adjusting the Sensitivity of the Auto Header Height Control (AHHC) (Gleaner
R65/R66/R75/R76 and Pre-2016 S Series) ..................................................................180
Troubleshooting Alarms and Diagnostic Faults (Gleaner R65/R66/R75/R76 and Pre-2016
S Series) ...................................................................................................................181
3.8.8 Gleaner S9 Series Combines ...................................................................................................183
Setting up the Header (Gleaner S9 Series) ...............................................................................183
Setting up Reel Settings (Gleaner S9 Series)............................................................................188
Setting up Automatic Header Controls (Gleaner S9 Series)........................................................189
Calibrating the Header (Gleaner S9 Series) ..............................................................................192
Operating Header (Gleaner S9 Series).....................................................................................195
Header In-Field Settings .........................................................................................................196
3.8.9 John Deere 60 Series Combines ..............................................................................................197
Checking Voltage Range from the Combine Cab (John Deere 60 Series)....................................197
Calibrating the Auto Header Height Control (John Deere 60 Series) ...........................................200
Turning the Accumulator Off (John Deere 60 Series) .................................................................201
Setting the Sensing Grain Header Height to 50 (John Deere 60 Series) ......................................202
Setting the Sensitivity of the Auto Header Height Control (John Deere 60 Series) ........................203
Adjusting the Threshold for the Drop Rate Valve (John Deere 60 Series) ....................................204
3.8.10 John Deere 70 Series Combines ............................................................................................205
Checking Voltage Range from the Combine Cab (John Deere 70 Series)....................................205
Calibrating Feeder House Speed (John Deere 70 Series) ..........................................................208
Calibrating the Auto Header Height Control (John Deere 70 Series) ...........................................208
Setting the Sensitivity of the Auto Header Height Control (John Deere 70 Series) ........................210
Adjusting the Manual Header Raise/Lower Rate (John Deere 70 Series) .................................... 211
3.8.11 John Deere S and T Series Combines.....................................................................................212
Checking Voltage Range from the Combine Cab (John Deere S and T Series) ............................212
Calibrating the Auto Header Height Control (John Deere S and T Series). ...................................215
Setting the Sensitivity of the Auto Header Height Control (John Deere S and T Series) ................218
Adjusting the Manual Header Raise/Lower Rate (John Deere S and T Series).............................219
Setting Preset Cutting Height (John Deere S and T Series)........................................................220
Calibrating Feeder House Fore-Aft Tilt Range (John Deere S and T Series) ................................222
Checking Reel Height Sensor Voltages (John Deere S and T Series) .........................................225
Calibrating Reel Height Sensor (John Deere S and T Series) .....................................................227
3.8.12 John Deere S7 Series Combines.. ..........................................................................................230
Setting up Header (John Deere S7 Series) ...............................................................................230
Checking Voltage Range from the Combine Cab (John Deere S7 Series) ...................................234
Calibrating Feeder House (John Deere S7 Series) ....................................................................236
Calibrating Header (John Deere S7 Series) ..............................................................................239
3.8.13 CLAAS 500 Series Combines.................................................................................................242
Calibrating the Auto Header Height Control (CLAAS 500 Series)................................................242
Setting Cutting Height (CLAAS 500 Series) ..............................................................................244
Setting the Sensitivity of the Auto Header Height Control (CLAAS 500 Series) ............................246
Adjusting Auto Reel Speed (CLAAS 500 Series) .......................................................................248
3.8.14 CLAAS 600 and 700 Series Combines....................................................................................251
Calibrating the Auto Header Height Control (CLAAS 600 and 700 Series) ...................................251
Setting Cutting Height (CLAAS 600 and 700 Series)..................................................................254
TABLE OF CONTENTS