Siemens FS20 - Page 123

To Next Page

To Previous Page

Updating the firmware

Station: Updating the FW of the main CPU and additional CPUs

123 |

188

Building Technologies

009052_s_en_

Fire Safety

2016

Starting the firmware update at the 'Station' – FCM2004

1. Select 'Initiate update at station'.

 The following window is opened:

2. Set the 'S38-2' switch to 'ON' on the rear of the operating unit.

3. Press the 'S32' button for approx. 5 s until the 'Station' restarts.

 The firmware update starts and takes up to ten minutes.

Main Page

Default Chapter3
- Table of Contents3
1 About this Document9
- Applicable Documents11
- Download Center11
- Technical Terms and Abbreviations12
- Revision History12
2 Safety16
- Safety Instructions16
- Safety Regulations for the Method of Operation18
- Standards and Directives Complied with20
  - CPR Conformity and Firmware Version20
- Release Notes20
- Cyber Security Disclaimer21
3 Mounting / Installation22
- Installing and Checking the Detector Line22
- Mount and Install 'Station23
4 Connectivity and Communication with 'Station24
- Setting Windows Firewall24
  - Windows XP24
  - Windows 7 / Windows 8 / Windows 1025
- Network Parameters26
- Connecting the PC to the Station27
- Disconnecting the PC from the Station27
- Loading Data to the 'Station28
- Initializing 'Station28
- Loading Configuration from the PC to the Station30
- Loading Configuration from the Station to the PC32
- Creating a Backup of the 'Site' Configuration32
5 Commissioning Overview34
- Commissioning Variants34
- Definition of Terms35
- Standard Gateway36
- Brief Instructions on Operating the 'Station36
- License37
6 Commissioning Standalone 'Station' Without PC38
- Configuring the Power Supply39
- Entering Customer Texts Using the Person Machine Interface39
- Setting Detector Parameter Sets40
7 B1 - Commissioning Standalone 'Station' with PC, Without Pre-Configuration41
8 B2 - Commissioning Standalone 'Station' with PC, with Pre-Configuration42
9 Commissioning Networked 'Stations43
10 Commissioning FC208044
11 Commissioning FG202045
12 Adding a 'Station' to an Existing 'Site46
13 Merging Two 'Sites47
- Adding 'Site' B to 'Site' a48
- Connecting 'Sites' Physically to One Another48
14 Changing and Expanding the Fdnet/C-NET Detector Line49
- Extending the Detector Line to Include Additional Devices49
  - Mount and Wire New Devices49
  - Configure a New Device50
- Replacing Stationary Devices of the same Type50
- Permanently Removing Stationary Devices51
- Removing or Replacing Non-Stationary Devices51
- Replacing 'Manual Call Point' of the same Type54
- Convert Two Stubs into a Loop56
- Connecting a Sub-Stub to a Loop56
15 Commissioning the Control Panel with Ms9I Detector Lines57
16 Commissioning Control Panel with Collective Detector Lines58
- Pre-Configuration58
- Reference Measurement with EOL 4K7 and 3K359
- Possible Error Messages59
  - Line Fault' Error Message60
- Troubleshooting Procedure60
17 Commissioning of Control Panel with Analogplus Detector Line64
18 Changing and Expanding the Analogplus Detector Line65
- Adding a Device to the Detector Line65
- Replacing a Device with One of a Different Type65
- Removing a Device Permanently66
- Replacing a Non-Stationary Device of the same Type66
- Replacing Multiple Non-Stationary Devices of the same Type with a Line Restart66
- Replacing Stationary Devices of the same Type67
- Converting a Stub or Loop67
- Querying the Number of Devices on the Detector Line67
- Readdressing Devices68
- Replacing an Analogplus Device68
19 Commissioning of Control Panel with Interactive Detector Line69
- Commissioning of Interactive Detector Line for Algorex Data Migration70
20 Changing and Expanding the Interactive Detector Line71
- Adding a Device to the Detector Line71
- Replacing a Device with One of a Different Type71
- Removing a Device Permanently72
- Replacing a Non-Stationary Device of the same Type72
- Replacing Stationary Devices of the same Type73
- Replacing Stationary Manual Call Points of the same Type73
- Converting a Stub or Loop74
- Replacing an Interactive Device74
- Locating Wire Breaks75
21 Detailed Commissioning Steps76
- Preparing 'Station' for Commissioning76
- Preparing 'Station' for Commissioning -Without BDV Installation77
- One-Step Commissioning78
- Auto-Configuring 'Station79
- Auto-Configuring the Detector Line79
- Loading Automatically Created Configuration to the PC80
- Adapting Configuration80
- Converting a Standalone Station to a Networked Station81
- Switch off82
  - Safety During Switch-Off82
  - Switching off the Detector Line82
  - Switch off Zone82
- Switching on83
  - Switch on Detector Line83
  - Switch on Zone83
- Restarting the Detector Line83
- Freezing Outputs84
- Enabling Frozen Outputs84
- Read in Devices on Detector Line85
- Detaching the Device85
- Delete the Device on Person Machine Interface86
- Remove the Elements86
- Testing Detectors87
  - Activate the Detector87
  - Testing Logged Test Activations87
- Using a Detector Exchanger and Tester or an Intelligent Detector Tester88
- Switching on Test Mode89
- Switch on Normal Operation90
- Rectify Localization Errors91
- Checking 'Site' Function91
- Carrying out Final Commissioning Work91
22 Commissioning Ethernet Switch (MM) FN2008-A192
- Install Primary Setup Tool92
- Assign IP Address93
- Configuring FN2008-A1 Using Internet Browser94
23 Commissioning Security Module (Firewall) FN2009-A195
- Installing Security Configuration Tool96
- Selecting Type and Entering MAC Address97
- Entering Network Settings98
- Creating IP Service Definitions100
- Creating Firewall Rules101
24 Commissioning Ethernet Switch (Modular) FN2012-A1103
- Standalone FN2012-A1103
  - Specifying a Pre-Configured IP Address104
- FN2012-A1 Integrated into Station105
- FN2012-A1 Web Interface106
- Restarting and Resetting the FN2012-A1110
25 Commissioning the Sounder Base FDSB291111
26 Commissioning the Fire Brigade Periphery Module FCI2001-D1112
27 Commissioning of I/O Card (Remote Transmission) FCI2007-A1 and I/O Card (Horn/Monitored) FCI2009-A1113
28 Commissioning External Printer114
29 Updating the Firmware117
- Preparation and Security117
- Station: Updating the FW of the Main CPU and Additional Cpus118
- Station: Updating the FW of the Additional Cpus Only132
- Update Only the BDV135
  - Standalone Station and SAFEDLINK Station135
  - Router Station and Ethernet Station136
- Converting the Configuration136
- Testing the Firmware Version of the Additional Cpus137
- Creating Diagnosis Report138
- Updating the FW of the Peripheral Devices138
- Updating the FW of Ethernet Switch (Modular) FN2012-A1154
  - Standalone FN2012-A1154
  - FN2012-A1 Integrated into Station157
30 Maintenance158
- General158
- Testing158
- Testing and Measuring Instruments159
- Preparatory Work160
- Test System Data160
- Testing the 'Station161
- Check the Power Supply162
- Testing the Printer162
- Checking 'Site' Function163
- Intervals for Testing the System Function163
- Carrying out Final Maintenance Work164
31 Repair165
- Disconnect the Station from the Power Supply165
- Spare Parts166
- Fault Messages on the Person Machine Interface166
- Fault Indicators on Components168
- Communication Problems in Networked Systems169
- Correcting Swapped Devices169
- Correcting an Invalid Topology170
- Error Message 'Too Many Devices170
- Restart the Station171
- Restoring Factory Setting on the Station172
- Fiber-Optic Network Module FN2006 / FN2007 Troubleshooting Steps174
- Glossary179
- Index182

Siemens FS20 - Page 123

Table of Contents

Other manuals for Siemens FS20

Related product manuals