Daedong DSC48 - Page 286

8
-2
Apr. 2007
DSC48
NUMBER
38T gear ............................................................ 4-34
A
Adjusting the belts ............................................. 1-18
Adjustment after installation .............................. 5-13
Adjustment and replacement of cutting blade unit
....................................................................... 3-6
Adjustment and replacement of feeding chain .... 4-8
Adjustment and replacement of feeding depth con-
trol chain ....................................................... 3-17
Adjustment and replacement of grain side chain
(LH) .............................................................. 3-14
Adjustment and replacement of grain side chain
(RH) .............................................................. 3-15
Adjustment and replacement of protrusion belt . 3-13
Adjustment and replacement of stem side chain
(LH) .............................................................. 3-14
Adjustment and replacement of stem side chain
(RH) .............................................................. 3-13
Adjustment and replacement of stem side feeding
chain ............................................................. 3-16
Adjustment of elevator chain tension and replace-
ment of elevator chain .................................. 3-10
Adjustment of neutral (stop) position ................ 6-24
After completing Intended operation and Storage
......................................................................0-11
After daily work is completed ..............................0-11
After daily work is completed ............................. 0-22
Air cleaner ......................................................... 2-20
Alarm buzzer, lamps on instrument panel and auto-
matic engine stop function .............................. 7-5
Alarm control ....................................................... 7-6
Alert symbols ....................................................... 0-3
American standard screws, bolts and nuts with UNC
or UNF threads ............................................. 1-15
Appearance ......................................................... 2-2
Area around engine .......................................... 5-14
Attachment .......................................................... 3-5
Avoid fi res ............................................................ 0-5
B
Base disc ........................................................... 4-35
Body ................................................................... 2-5
Brake turn (right turn) .......................................... 5-3
C
Cam clutch of reaping drive pulley ...................... 5-6
Camshaft ............................................................. 2-7
Cautions for high pressure hoses ........................ 0-6
Cautions when handling the battery .................... 0-6
Charge lamp (instrument panel) ........................ 7-10
Charge lamp ...................................................... 7-15
Charge pump ..................................................... 6-18
Charge relief valve............................................. 6-19
Check and adjustment of area around engine... 5-14
Check and adjustment of belt .............................. 4-6
Check and adjustment of cutter ......................... 4-29
Check and adjustment of HST ........................... 6-24
Check and adjustment of hydraulic system ....... 6-13
Check and adjustment of straw discharging chain
..................................................................... 4-25
Check and maintenance ................................... 1-17
Check before operation ....................................... 0-9
Check before starting engine............................. 1-17
Check for normal operation of hydraulic system .6-11
Check for normal operation of instrument panel.. 7-3
Check for normal operation of load level ........... 7-18
Check for pressure of high pressure relief valve . 6-14
Check for pressure of low pressure relief valve . 6-13
Check for relief valve pressure .......................... 6-24
Check lamp (instrument panel)............................ 7-9
Check, disassembly and adjustment ................. 2-29
Checking automatic engine stop relay............... 7-33
Checking automatic feeding depth control switch
(AFC) ............................................................ 7-38
Checking buzzers (front and rear) ..................... 7-39
Checking each level .......................................... 7-18
Checking each part ........................................... 7-33
Checking electronic pick up sensor ................... 7-35
Checking engine stop motor .............................. 7-34
Checking feeding depth control motor ............... 7-33
Checking feeding depth control stop switch ...... 7-39
Checking fuel gauge unit ................................... 7-34
Checking grain sensor (grain switch) ................ 7-35
Checking grain sensor ....................................... 7-36
Checking ignition switch .................................... 7-37