8
-4
Apr. 2007
DSC48
Every 300 hours ................................................ 1-32
Every 350 hours ................................................ 1-34
Every 400 hours ................................................ 1-35
Every 50 hours .................................................. 1-25
Every 500 hours ................................................ 1-37
Every 600 hours ................................................ 1-38
Every 800 hours ................................................ 1-38
Exploded view ................................................... 2-29
External components ......................................... 2-31
F
Feeding chain ...................................................... 4-8
Feeding depth control motor and limit switch .... 7-25
Feeding depth control ........................................ 7-19
Flasher unit resistance (S)................................. 7-34
Flow of cooling water ..........................................2-11
Flow of fuel ........................................................ 2-13
Flow of intake air and exhaust gas .................... 2-20
Flow of lubricating oil ........................................... 2-9
Flywheel .............................................................. 2-8
For long-term storage ........................................ 0-24
For safety............................................................. 0-3
For your safety..................................................... 0-9
Front section of threshing cylinder....................... 4-6
Fuel camshaft ...................................................... 2-7
Fuel feed pump.................................................. 2-13
Fuel injection nozzle .......................................... 2-16
Fuel injection pump ........................................... 2-14
Fuel system check ............................................. 2-57
Fuel system specifi cations................................. 2-27
Fuel system ....................................................... 2-13
G
General precaution before operation ................. 0-12
General precautions ............................................ 2-4
General specifi cations ......................................... 2-3
General use bolts and nuts................................ 1-14
General ................................................................ 2-2
Governor............................................................ 2-17
Grain alarm (alarm buzzer and instrument panel) . 7-7
Grain alarm ........................................................ 7-13
Grain sensor alarm (alarm buzzer, etc.) .............. 7-9
Grain sensor and feeding depth control motor out-
put ................................................................ 7-19
H
Handling of hazardous materials ......................... 0-7
Handling of rotating blade, shaft and driving belt 0-7
Harvesting ..........................................................0-11
HST (Hydrostatic Transmission) ........................ 6-16
HST hose diagram and pressure check ............ 6-20
HST troubleshooting list .................................... 6-21
Hydraulic system ................................................. 6-3
I
Ignition switch for alarm control ......................... 7-10
Ignition switch for load level............................... 7-18
Ignition switch troubleshooting ......................... 7-16
Illumination .......................................................... 0-4
Initial 50 hours ................................................... 1-19
Installation of chain lock plate............................ 3-20
Installation of feeding chain ............................... 3-21
Installation of feeding depth control chain ......... 3-21
Installation of feeding guide ............................... 3-21
Installation of front cover ................................... 4-14
Installation of stem side conveyor prop ............. 3-19
Installation of stem side prop ............................. 3-20
Intake and exhaust system ................................ 2-20
Intake and exhaust valves ................................... 2-8
L
Large-diameter washer of stem side support spring
..................................................................... 3-19
Lever switch 1 (turning left/right lever)............... 7-40
Lever switch 2 (reaping unit up/down lever) ...... 7-40
LH on threshing unit ............................................ 4-7
Lifting and lowering reaping unit .......................... 6-4
Lifting and lowering the reaping unit ................. 7-27
Liquid gasket application ................................... 1-12
Load alarm (alarm buzzer and instrument panel) . 7-8
Load alarm......................................................... 7-15
Load level control .............................................. 7-17
Load level .......................................................... 7-17
Loading and unloading the combine harvester to the
transporting vehicle ...................................... 0-10
To Next Page
Loading...
