Motion Control Engineering Motion 4000 User Manual

Index-3
Commanded and actual pick voltage 4-116
Communication baud rate, External CAN bus 5-41
Complimented PTI Input 4-32
Computer Generated Fault Output 4-36
Computer Internal Memory 4-6
conF 2-21
CONFIGURATION ERROR CHANGE SETTINGS BEFORE
INSTALLATION 5-6
Connection Set 1-16
Connections screen 4-113
CONST. PRESS OP. BYPASS PHE 4-21
Construction operation 2-28
Construction operation jumpers 2-28
CONT. D.C.B. FOR FIRE PH 1 option 4-20
CONT. D.C.B. TO CLOSE DOORS option 4-20
Contactor Proof Input 4-28
CONTRACT OVERSPEED 5-21, 5-30
Contract Overspeed 4-135
Contract Speed 4-135
Control parameters
KEB/Torqmax, Magnetek 2-46
Controller inspection 2-54
Controller reset 4-4
CORRECTION AWAY FROM CW 4-49
Correction Speed 4-136
Counterweight balancing, preparing for final adjust 3-8
Counterweight Input 4-28
Counterweight Position 4-127
Counterweight Safety Test 3-44
CR01-CR8 4-36
CR01R-CR8R 4-37
CR1-CR8 4-28
CR1R-CR8R 4-28
CR2032 battery voltage 5-6
CRO 4-28
CSA FAULT OUTPUT 4-36
CSB, Car stop switch bypass flag 4-9
CSB, Car Stop Switch Bypass Output option 4-37
CSBR, Car stop switch bypass (rear) flag 4-9
CSEO, Code Sequence Enable Output option 4-37
CSR, Car Selected to Run Output option 4-37
CTF
Car To Floor 1-15
CTL
Car to Lobby 1-15
CTL, Car to lobby input flag 4-9
CTL, Car-to-Lobby Input option 4-28
CTLDOT, Car to lobby door open timer flag 4-9
CTLDOT, Car-to-Lobby Door Open Timer Output option 4-37
CTLF, Car to lobby function flag 4-9
CTP, Car to floor Input option 4-28
CTST, Capture for test input flag 4-9
CTST, Capture for Test Input option 4-28
CWI 4-28
CYCLE TEST 5-6
D
D = Dispatcher 4-6
D in upper left corner of the LCD 5-38
D.C.B. CANCELS DOOR TIME option 4-19
d.LF.32 2-33, A-3
Danger “Curve” 3-12
Danger Deceleration 4-137
Danger Roll Jerk 4-137
Danger Slew Slope 4-134
Danger Start Jerk 4-137
Danger Stop Jerk 4-137
Date / Time Stamp 4-63
Date/Time, View / Adjust 4-63
DBC, Door close button input flag 4-9
DBCR, Door close button (rear) flag 4-9
DBZF, Front Door Buzzer output option 4-37
DBZR, Rear Door Buzzer output option 4-37
DC, Down call flag 4-9
DCA, Down call above flag 4-9
DCAB INPUT FAILURE 5-6
DCB, Down call below flag 4-9
DCC, Door close complete flag 4-9
DCCR, Door close complete flag (rear) 4-9
DCF, Door close function output flag 4-9
DCFR, Door close function output (rear) flag 4-9
DCFRX 4-37
DCFX 4-37
DCL, Door Close Limit Input option 4-28
DCLC 4-9
DCLC, Doors Closed Contact Input option 4-28
DCLCR INPUT FAILURE 5-7
DCLCR, Door close contact input (rear) flag 4-9
DCLR 4-28
DCP, Door close power output flag 4-9
DCPR, Door close power output (rear) flag 4-9
DCPRX 4-37
DCPX 4-37
DCR, Down call flag (rear) flag 4-9
DDF, Double ding function flag 4-9
DDP, Down direction preference flag 4-9
DEADZ, Dead zone flag 4-9
Deceleration parameter 3-13
DEDICATED PI BOARD? 4-15
Default brake module values 4-116
Default parameter values 4-5
Default TC-FCL Parameters 4-116
Default TC-MPI Parameters 4-65
Default the TC-MPI 4-65
Default XPort screen 4-115
DEIS 4-38
DEISR 4-38
Delta speeds 4-130
DETS 4-132
DETS Delta Distance, 106 4-132
DETS Delta High Speed 4-132
DETS Distance 4-132
DETS POSITION FAULT 5-22
DETS Speed 4-132
Device Data screen 4-114
DFI 4-28

Motion Control Engineering Motion 4000 Specifications

General

Brand	Motion Control Engineering
Model	Motion 4000
Category	Controller
Language	English