Omron RX Series - Page 437

7 - 111
7 Detailed Functions
High-function General-purpose Inverter 3G3RX-V1 User’s Manual (I578-E1)
7-5 Multi-function Terminal Functions (Group C)
7
• Use this function to control three motors by switching.
• To switch among three motors, set the Multi-function Input S1 to S8 Selection (C001 to C008) to 08
(SET) or 17 (SET3) and turn ON/OFF the terminal SET or SET3.
*1 *: For these parameters, data can be changed during operation.
2nd/3rd Control Functions
The functions that support switching of motor via the SET/SET3 terminal
are as follows.
F002/F202/F302
*1
: 1st/2nd/3rd Acceleration Time 1
F003/F203/F303
*1
: 1st/2nd/3rd Deceleration Time 1
A003/A203/A303: 1st/2nd/3rd Base Frequency
A004/A204/A304: 1st/2nd/3rd Maximum Frequency
A020/A220/A320
*1
: 1st/2nd/3rd Multi-step Speed Reference 0
A041/A241: 1st/2nd Torque Boost Selection
A042/A242/A342
*1
: 1st/2nd/3rd Manual Torque Boost Voltage
A043/A243/A343
*1
: 1st/2nd/3rd Manual Torque Boost Frequency
A044/A244/A344: 1st/2nd/3rd Control Method
A046/A246
*1
: 1st/2nd Automatic Torque Boost Voltage
Compensation Gain
A047/A247
*1
: 1st/2nd Automatic Torque Boost Slip
Compensation Gain
A061/A261
*1
: 1st/2nd Frequency Upper Limit
A062/A262
*1
: 1st/2nd Frequency Lower Limit
A092/A292/A392
*1
: 1st/2nd/3rd Acceleration Time 2
A093/A293/A393
*1
: 1st/2nd/3rd Deceleration Time 2
A094/A294: 1st/2nd 2-step Acceleration/Deceleration
Selection
A095/A295: 1st/2nd 2-step Acceleration Frequency
A096/A296: 1st/2nd 2-step Deceleration Frequency
b012/b212/b312
*1
: 1st/2nd/3rd Electronic Thermal Level
b013/b213/b313
*1
: 1st/2nd/3rd Electronic Thermal Characteristics
Selection
H002/H202: 1st/2nd Motor Parameter selection
H003/H203: 1st/2nd Motor Capacity
H004/H204: 1st/2nd Motor Pole Number
H005/H205
*1
: 1st/2nd Speed Response
H006/H206/H306
*1
: 1st/2nd/3rd Stabilization Parameter
H020/H220: 1st/2nd Motor Parameter R1
H021/H221: 1st/2nd Motor Parameter R2
H022/H222: 1st/2nd Motor Parameter L
H023/H223: 1st/2nd Motor Parameter Io
H024/H224: 1st/2nd Motor Parameter J
H030/H230: 1st/2nd Motor Parameter R1 (Auto-tuning
Data)
H031/H231: 1st/2nd Motor Parameter R2 (Auto-tuning
Data)
H032/H232: 1st/2nd Motor Parameter L (Auto-tuning Data)
H033/H233: 1st/2nd Motor Parameter Io (Auto-tuning Data)
H034/H234: 1st/2nd Motor Parameter J (Auto-tuning Data)
H050/H250*: 1st/2nd PI Proportional Gain
H051/H251*: 1st/2nd PI Integral Gain
H052/H252*: 1st/2nd P Proportional Gain
H060/H260*: 1st/2nd Limit at 0 Hz
U/T1
V/T2
W/T3
SET
SET3
SC
Motor
1
Motor
2
Motor
3
Inverter