EasyManua.ls Logo

Omron ZW-7000 Series - Page 18

Omron ZW-7000 Series
290 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
16
ZW-7000/5000
User's Manual
Connection of Fiber Cable and Calibration ROM . . . . . . . . . . . . . . . . . . . . . . .55
Remove the Fiber cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Cleaning the fiber connector and fiber cable using ZW-XCL . . . . . . . . . . . . . . 60
Extending fiber cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Calibrating Sensor Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2-4 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
32-pole extension connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Analog output terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
24 V input terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
2-5 Installing the Sysmac Studio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2-6 Launching a project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Connecting to the sensor with Sysmac Studio Measurement Sensor Edition . . 79
Entering project information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2-7 Explanation of Screen Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
PC tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2-8 Saving a project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Saving a project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Exporting a project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Importing a project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3.Basic Operation
3-1 Setting the Measurement Start Timing . . . . . . . . . . . . . . . . . . . . . . . . 88
Internal Processing of Sensor Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Measurement Mode and Measurement Start Timing . . . . . . . . . . . . . . . . . . . . 89
3-2 Switching operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
3-3 Displaying Measured Values and Received
Light Waveform . . . . . . 91
3-4 Perform the Zero Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Zero reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
3-5 Displaying measured values in graphs. . . . . . . . . . . . . . . . . . . . . . . . 95
Specifying the sampling start and end conditions . . . . . . . . . . . . . . . . . . . . . . . 97
Starting and ending sampling before and after the trigger condition is met . . 100
Adjusting the scale of the axis in a graph automatically according to the measure-
ment values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
3-6 Saving measured values in a file. . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Outputting the results of sampling as a file . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Exporting the results of sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
3-7 Displaying saved measured values. . . . . . . . . . . . . . . . . . . . . . . . . . 105
3-8 Performing internal logging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Internal logging by Sysmac Studio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Performing Internal Logging with Parallel I/O . . . . . . . . . . . . . . . . . . . . . . . . . 108
3-9 Bank switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Table of Contents

Related product manuals