EasyManua.ls Logo

Siemens 7SJ85 - Settings

Siemens 7SJ85
1638 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
You can use the Dropout delay parameter ≠ 0 s to obtain a uniform dropout behavior if you use it
together with an electromechanical relay. This is required for time grading. The dropout time of the electro-
mechanical relay must be known for this purpose. Subtract the dropout time of your own device (see Tech-
nical Data) and set the result.
Settings
Addr. Parameter C Setting Options Default Setting
General
_:2311:102 General:Rotation angle
of ref. volt.
-180 ° to 180 ° 45 °
General
_:8131:1 Definite-T 1:Mode
off
on
test
off
_:8131:2 Definite-T 1:Operate &
flt.rec. blocked
no
yes
no
_:8131:105 Definite-T 1:Directional
mode
forward
reverse
forward
_:8131:8 Definite-T 1:Method of
measurement
fundamental comp.
RMS value
fundamental
comp.
_:8131:107 Definite-T 1:Non-direc-
tional pickup
no
at volt.< & mem.empty
at volt.< &
mem.empty
_:8131:104 Definite-T 1:Directional
comparison
no
yes
no
_:8131:106 Definite-T 1:Release via
input signal
no
yes
no
_:8131:10 Definite-T 1:Blk. by
meas.-volt. failure
no
yes
yes
_:8131:26 Definite-T 1:Dynamic
settings
no
yes
no
_:8131:27 Definite-T 1:Blk. w.
inrush curr. detect.
no
yes
no
_:8131:3 Definite-T 1:Threshold 1 A @ 100 Irated 0.030 A to 35.000 A 1.500 A
5 A @ 100 Irated 0.15 A to 175.00 A 7.50 A
1 A @ 50 Irated 0.030 A to 35.000 A 1.500 A
5 A @ 50 Irated 0.15 A to 175.00 A 7.50 A
1 A @ 1.6 Irated 0.001 A to 1.600 A 1.500 A
5 A @ 1.6 Irated 0.005 A to 8.000 A 7.500 A
_:8131:4 Definite-T 1:Dropout
ratio
0.90 to 0.99 0.95
_:8131:101 Definite-T 1:Dropout
delay
0.00 s to 60.00 s 0.00 s
_:8131:6 Definite-T 1:Operate
delay
0.00 s to 60.00 s 0.30 s
Dyn.s: AR off/n.rdy
_:8131:28 Definite-T 1:Effect. by AR
off/n.ready
no
yes
no
_:8131:35 Definite-T 1:Stage
blocked
no
yes
no
Dyn.set: AR cycle 1
_:8131:29 Definite-T 1:Effected by
AR cycle 1
no
yes
no
6.6.4.3
Protection and Automation Functions
6.6 Directional Overcurrent Protection, Phases
416 SIPROTEC 5, Overcurrent Protection, Manual
C53000-G5040-C017-8, Edition 07.2017

Table of Contents

Related product manuals