Siemens 7SJ85 - Settings; Information List

The Operate delay parameter determines the time during which the pickup conditions must be met to
issue the operate indication. The operate indication is issued when this time expires.
Settings
Addr. Parameter C Setting Options Default Setting
3I0> φ(VI) #
_:1 3I0> φ(VI) #:Mode
•
off
•
on
•
test
off
_:2 3I0> φ(VI) #:Operate &
flt.rec. blocked
•
no
•
yes
no
_:10 3I0> φ(VI) #:Blk. by
meas.-volt. failure
•
no
•
yes
yes
_:27 3I0> φ(VI) #:Blk. w.
inrush curr. detect.
•
no
•
yes
no
_:106 3I0> φ(VI) #:Directional
mode
•
non-directional
•
forward
•
reverse
forward
_:104 3I0> φ(VI) #:Rotation
angle of ref. volt.
-180 ° to 180 ° -45 °
_:103 3I0> φ(VI) #:Forward
section +/-
0 ° to 180 ° 88 °
_:102 3I0> φ(VI) #:Min. V0>
for dir. determ.
0.300 V to 200.000 V 2.000 V
_:101 3I0> φ(VI) #:3I0>
threshold value
1 A @ 100 Irated 0.030 A to 35.000 A 0.050 A
5 A @ 100 Irated 0.15 A to 175.00 A 0.25 A
1 A @ 50 Irated 0.030 A to 35.000 A 0.050 A
5 A @ 50 Irated 0.15 A to 175.00 A 0.25 A
1 A @ 1.6 Irated 0.001 A to 1.600 A 0.050 A
5 A @ 1.6 Irated 0.005 A to 8.000 A 0.250 A
_:105 3I0> φ(VI) #:Dir. deter-
mination delay
0.00 s to 60.00 s 0.10 s
_:6 3I0> φ(VI) #:Operate
delay
0.00 s to 60.00 s 0.50 s
Information List
No.
Information Data Class
(Type)
Type
3I0> φ(VI) #
_:81 3I0> φ(VI) #:>Block stage SPS I
_:501 3I0> φ(VI) #:>Block delay & op. SPS I
_:54 3I0> φ(VI) #:Inactive SPS O
_:52 3I0> φ(VI) #:Behavior ENS O
_:53 3I0> φ(VI) #:Health ENS O
_:301 3I0> φ(VI) #:Fault not in trip area SPS O
_:60 3I0> φ(VI) #:Inrush blocks operate ACT O
_:303 3I0> φ(VI) #:Ground fault ACD O
_:55 3I0> φ(VI) #:Pickup ACD O
_:56 3I0> φ(VI) #:Operate delay expired ACT O
_:57 3I0> φ(VI) #:Operate ACT O
6.15.7.3
6.15.7.4
Protection and Automation Functions
6.15 Sensitive Ground-Fault Detection
SIPROTEC 5, Overcurrent Protection, Manual 591
C53000-G5040-C017-8, Edition 07.2017