EasyManuals Logo

ST STM32F2 User Manual

ST STM32F2
1371 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #207 background imageLoading...
Page #207 background image
UM1940
HAL ETH Generic Driver
DocID028236 Rev 2
207/1371
uint32_t ETH_DMAInitTypeDef::ForwardErrorFrames
Selects or not the forward to the DMA of erroneous frames. This parameter can be a
value of ETH_Forward_Error_Frames
uint32_t ETH_DMAInitTypeDef::ForwardUndersizedGoodFrames
Enables or disables the Rx FIFO to forward Undersized frames (frames with no Error
and length less than 64 bytes) including pad-bytes and CRC) This parameter can be a
value of ETH_Forward_Undersized_Good_Frames
uint32_t ETH_DMAInitTypeDef::ReceiveThresholdControl
Selects the threshold level of the Receive FIFO. This parameter can be a value of
ETH_Receive_Threshold_Control
uint32_t ETH_DMAInitTypeDef::SecondFrameOperate
Selects or not the Operate on second frame mode, which allows the DMA to process a
second frame of Transmit data even before obtaining the status for the first frame.
This parameter can be a value of ETH_Second_Frame_Operate
uint32_t ETH_DMAInitTypeDef::AddressAlignedBeats
Enables or disables the Address Aligned Beats. This parameter can be a value of
ETH_Address_Aligned_Beats
uint32_t ETH_DMAInitTypeDef::FixedBurst
Enables or disables the AHB Master interface fixed burst transfers. This parameter
can be a value of ETH_Fixed_Burst
uint32_t ETH_DMAInitTypeDef::RxDMABurstLength
Indicates the maximum number of beats to be transferred in one Rx DMA transaction.
This parameter can be a value of ETH_Rx_DMA_Burst_Length
uint32_t ETH_DMAInitTypeDef::TxDMABurstLength
Indicates the maximum number of beats to be transferred in one Tx DMA transaction.
This parameter can be a value of ETH_Tx_DMA_Burst_Length
uint32_t ETH_DMAInitTypeDef::EnhancedDescriptorFormat
Enables the enhanced descriptor format. This parameter can be a value of
ETH_DMA_Enhanced_descriptor_format
uint32_t ETH_DMAInitTypeDef::DescriptorSkipLength
Specifies the number of word to skip between two unchained descriptors (Ring mode)
This parameter must be a number between Min_Data = 0 and Max_Data = 32
uint32_t ETH_DMAInitTypeDef::DMAArbitration
Selects the DMA Tx/Rx arbitration. This parameter can be a value of
ETH_DMA_Arbitration
17.1.4 ETH_DMADescTypeDef
Data Fields
__IO uint32_t Status
uint32_t ControlBufferSize
uint32_t Buffer1Addr
uint32_t Buffer2NextDescAddr
uint32_t ExtendedStatus
uint32_t Reserved1
uint32_t TimeStampLow
uint32_t TimeStampHigh
Field Documentation
__IO uint32_t ETH_DMADescTypeDef::Status
Status
uint32_t ETH_DMADescTypeDef::ControlBufferSize
Control and Buffer1, Buffer2 lengths

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ST STM32F2 and is the answer not in the manual?

ST STM32F2 Specifications

General IconGeneral
BrandST
ModelSTM32F2
CategoryMicrocontrollers
LanguageEnglish

Related product manuals