Index-4
IM MW100-01E
plate with screw terminal ...................................................... 2-8
pollution degree .................................................................... 5-1
POP3 .............................................................................. App-18
POP3 server ....................................................................... 3-47
POP before SMTP .......................................................... App-18
power consumption ............................................................ 5-24
power cord .......................................................................... 2-20
power failure notification ..................................................... 3-48
power ON operation ........................................................... 3-38
power supply ...................................................................... 2-20
power supply frequency........................................................ 5-1
power supply terminal................................................ 2-21, 2-22
pre-trigger ........................................................................... 3-20
preset value ............................................................... 3-36, 3-37
pretrigger function........................................................ 1-20, 5-9
primary and secondary boxes ............................................ 3-46
processing and operation ................................................... 3-17
processing upon math error................................................ 1-56
program channel.................................................... 3-30, App-19
program channels ........................................... 1-53, 5-5, App-19
pulse interval ............................................................. 1-43, 3-37
pulse resolution .................................................................. 3-37
R
rack mounting ....................................................................... 2-2
range calibration ................................................................. 4-12
rated power supply voltage................................................... 5-1
rate of change interval ........................................................ 3-16
rate of change lower limit alarm.......................................... 1-16
rate of change upper limit alarm ......................................... 1-16
receive data control ............................................................ 2-28
receiver settings ................................................................... 3-7
receive timeout ................................................................... 5-20
recipient .............................................................................. 3-48
recorder structure ................................................................. 5-8
recording channels ............................................................... 5-9
recording channel settings.................................................. 3-22
recording interval ................................................................ 5-10
recording operation settings ............................................... 3-20
recording start action ................................................... 1-19, 5-9
recording stop action ................................................... 1-19, 5-9
rec start...................................................................... 3-44, 3-53
rec stop ...................................................................... 3-44, 3-53
ref.time................................................................................ 3-49
reference junction compensation...................... 1-14, 3-27, 4-16
reference junction compensation accuracy ............... 5-29, 5-33
reflash alarm ......................................................................... 5-7
reflash function ................................................................... 1-49
reflash setting ..................................................................... 3-34
register assign .................................................................... 5-18
relational operations ........................................................... 1-51
relative time timer ............................................. 1-18, 3-41, 5-21
relay excitation state ........................................................... 1-48
relay output factor settings ................................................. 3-34
relay settings ...................................................................... 3-34
remote RJC ........................................................................ 1-14
remote RJC (RRJC) reference channel.............................. 3-23
replacing CF card while recording ...................................... 1-22
resistance ........................................................................... 1-36
resistance temperature detector .............. 1-30, 1-33, 1-35, 1-36
retries, number of ............................................................... 5-17
rolling average ............................................................. 1-55, 5-5
rotate .................................................................................. 1-19
RRJC .................................................................................. 1-14
RS-232 communication ...................................................... 1-26
RS-232 interface........................................................ 2-28, 5-15
RS-422A/485 communication ............................................. 1-26
RS-422A/485 interface ....................................................... 2-25
S
saved items ........................................................................ 5-12
saving/loading setup data ................................................... 3-51
saving alarm summaries..................................................... 1-28
saving computed data ........................................................ 1-21
saving measured data ........................................................ 1-21
saving recorded data in divisions ....................................... 1-22
saving recording log files .................................................... 1-27
saving settings .................................................. 1-22, 3-51, 5-12
saving thinned data ............................................................ 1-21
saving thinning recorded data in divisions .......................... 1-22
scale input methods............................................................ 3-26
screw terminal block ............................................................. 2-8
selecting action type ........................................................... 3-40
selecting event detection method ....................................... 3-40
selecting event type ............................................................ 3-40
self-test operation ................................................................ 1-11
send data control ................................................................ 2-28
sender................................................................................. 3-48
serial number ...................................................................... 3-14
server list settings ............................................................... 3-50
server settings .................................................................... 3-50
services, list of .................................................................... 5-13
setting folders ..................................................................... 1-21
setting mode ................................................................ 1-16, 3-4
setting module information ................................................. 3-13
setting operation upon error occurrence............................. 3-38
setting power on operation ................................................. 3-38
settings errors ....................................................................... 4-2
setting the filter coefficient .................................................. 3-26
setting the input range ........................................................ 3-23
setting the match time ........................................................ 3-42
setting the math span ......................................................... 3-28
setting the measurement range .......................................... 3-23
setting the measurement span ........................................... 3-23
signal names ............................................................. 2-25, 2-28
single .................................................................................. 1-19
single screen ...................................................................... 3-52
slave address ..................................................................... 5-17
slide zone ........................................................................... 3-55
slot cover ............................................................................ 2-33
SMTP ............................................................ 1-23, 5-13, App-18
SMTP client function ........................................................... 3-47
SNTP ............................................................ 2-31, 5-13, App-18
SNTP function .................................................................... 1-23
special math processing ..................................................... 1-56
standards compliance........................................................... 5-1
start bit ................................................................................ 5-15
starting computation .................................................. 1-54, 3-44
starting measurement ......................................................... 3-43
starting recording ................................................................ 3-44
start number ....................................................................... 3-22
status .................................................................................. 1-16
status bar ............................................................................ 3-54
status indicators.................................................................. 3-45
status information ............................................................... 3-16
steady output operation ...................................................... 1-46
stop bit ................................................................................ 5-15
stopping computation ................................................ 1-54, 3-44
stopping measurement ....................................................... 3-43
stopping recording .............................................................. 3-44
storage conditions ................................................................ 5-1
strain input .......................................................................... 1-37
style number ..... i, 5-2, 5-27, 5-31, 5-35, 5-39, 5-42, 5-43, 5-45,
5-48
subnet mask ................................................................... App-18
supply voltage range used.................................................... 5-1
supported external media ..................................................... 5-9
Index
To Next Page
Loading...
Need help?
General
