EDM Solution 862 - Connections of Split EOL Resistors Using N;O Contacts

262 pages

Save Page as PDF

To Next Page

To Previous Page

160

Solution 862

Installation Manual

Connections Of Split EOL Resistors Using N/O Contacts

Figure 8: Connections Of Split EOL Resistors Using One N/O Contact

Figure 9: Connections Of Split EOL Using Two N/O Contacts

ISSUE130 Electronics Design and Manufacturing Pty Limited

Main Page

Installation Manual5
Introduction15
Introduction16
Features17
Quick Start18
Zone Defaults20
Programming21
Programming22
Programming with the Remote Codepad23
Programming with the Hand Held Programmer25
Programming with the Programming Key27
Programming Option Bits28
Installer's Programming Commands29
Command 958 - Enable/Disable Zone Status Mode30
Command 959 - Test Programming Key31
Command 960 - Exit Installer's Programming Mode33
Command 962 - Copy Control Panel Memory to Programming Key34
Command 963 - Copy from Programming Key to Control Panel35
Command 964 - Erase Programming Key36
Command 965 - Set up Domestic Dialling Format37
Command 966 - Enable/Disable Automatic Stepping of Locations38
Command 999 - Display Panel Type or Software Version Number40
Disable Factory Default41
Defaulting the Control Panel42
Codepad Indicators43
CP5 Eight Zone LED Codepad44
STAY Indicator45
Audible Indicators46
CP5 Eight Zone LCD Codepad47
STAY Indicator48
FAULT Indicator49
Audible Indicators50
System Operations51
System Operations52
Disarming the System from AWAY Mode53
Arming the System in STAY Mode 154
Forced Arming55
Disarming the System from STAY Mode 156
Arming the System in STAY Mode 257
Disarming the System from STAY Mode 258
Codepad Duress Alarm59
Isolating Zones60
Standard Isolating61
Code to Isolate62
Fault Analysis Mode63
Fault Descriptions64
Fuse Fail65
AC Mains Failure66
Remote Radio Transmitter Operations67
Remote Radio Transmitter Operations68
Changing or Deleting Remote Radio User Codes69
Channel Radio Remote Hand Held Transmitter Operations71
Channel Radio Remote Hand Held Transmitter Operations72
Turning Output 1 on73
System Functions75
System Functions76
Set the Number of Days until the First Test Report77
Changing Domestic Phone Numbers78
Change Telco Arm/Disarm Sequence80
Setting STAY Mode 2 Zones85
Satellite Siren Service Mode86
Turning Telephone Monitor Mode On/Off87
Event Memory Recall Mode88
Master Code Functions89
Changing and Deleting User Codes90
Changing and Deleting Remote Radio User Codes92
Changing Domestic Phone Numbers94
Change Telco Arm/Disarm Sequence96
Setting STAY Mode 2 Zones101
Turning Outputs On/Off102
Setting the Date and Time104
Walk Test Mode105
Event Memory Recall Mode106
Hold down Functions107
Bell Test108
Fault Analysis Mode109
Codepad Buzzer Tone Change110
Remote System111
Remote Arming Via the Telephone112
Alarm Link Operations113
Alarm Link Software114
Remote Connect Without Call Back Verification115
Direct Connect116
Alarm Link Options117
Domestic Dialling119
Domestic Dialling Format120
Setting up and Programming Domestic Reporting121
Disable Domestic Dialling122
Dialler Reporting Formats123
Transmission Formats124
Point ID Codes125
Reporting Format126
Basic Pager Reporting Format127
Basic Pager Display Information128
Dialler Information129
Dialler Information130
Primary Telephone Number for Receiver 1131
Handshake Tone for Receiver 1132
Transmission Format for Receiver 1133
Primary Telephone Number for Receiver 2134
Handshake Tone for Receiver 2135
Transmission Format for Receiver 2136
Dialling Format137
Telco Arming Sequence138
Telco Disarming Sequence139
Ring Count140
Telephone Line Fault Options141
Ring Burst Time142
Dialler Options143
Programming Option Bits144
Dialler Options 1145
Dialler Options 2146
Dialler Options 3147
Alarm Link Options148
User Codes149
Access Codes150
User Codes151
User Codes152
User Code Priority153
Zone Information155
Day Alarm Zones156
Day Alarm Operation157
EOL Resistor Value158
Connections of Split EOL Resistors Using N/C Contacts159
Connections of Split EOL Resistors Using N/O Contacts160
Zone Programming161
Solution 862 Zones Defaults162
Delay-1 Zone163
Keyswitch Zone164
Zone Pulse Count165
Zone Pulse Count Time166
Zone Options 1167
Silent Alarm168
Keyswitch Zone Options169
Momentary Arm and Disarm in AWAY Mode170
Zone Options 2171
Zone Reporting Information172
Swinger Shutdown Count for Siren173
Swinger Shutdown Count for Dialler174
System Reporting Information175
Reporting Information176
Zone Status – Trouble Reports177
Zone Status – Sensor Watch Reports178
Open/Close Reports179
Codepad Duress Report180
Codepad Fire Report181
Codepad Reporting Options182
System Status – AC Fail Report183
System Status - Low Battery Report184
System Status - Access Denied185
System Status Reporting Options186
Test Reporting Time187
Programmable Outputs189
Outputs190
Redirecting Outputs to the Codepad Buzzer191
Output Event Types192
Output Polarity199
Normally Open, One Shot Low with Alarm200
Timing of Outputs201
One Shot Polarities202
System Event Timers203
System Event Timers204
Exit Time205
Sensor Watch Time206
Siren Run Time207
Auto Arming Pre-Alert Timer208
Auto Disarming Time209
System Time210
System Date211
System and Consumer Options213
Programming Option Bits214
System Options 1215
System Options 2216
System Options 3217
System Options 4218
Consumer Options 1219
Consumer Options 2220
Consumer Options 3221
Radio Input Options222
Optional Equipment223
Optional Equipment224
Terminals and Descriptions229
Terminal Definitions and Descriptions230
Glossary of Terms231
Solution 862 Wiring Diagram234
Solution 862 Component Overlay235
Telecom Connection Diagrams236
Appendices237
Appendix A238
Appendix B239
Specifications241
Warranty Statement242
Specifications243
New Zealand Telepermit Notes244
Programming Sheets245
Index255

EDM Solution 862 - Connections of Split EOL Resistors Using N;O Contacts

Table of Contents

Other manuals for EDM Solution 862

Related product manuals