Menu 5 Single Line Descriptions − Motor Control
Mode: Open‑loop
Parameter Range Default Type
05.001 Output Frequency ±VM_SPEED_FREQ_REF Hz RO Num ND NC PT FI
05.002 Output Voltage ±VM_AC_VOLTAGE V RO Num ND NC PT FI
05.003 Output Power ±VM_POWER kW RO Num ND NC PT FI
05.004 Motor Rpm ±33000 rpm RO Num ND NC PT FI
05.005 D.c. Link Voltage ±VM_DC_VOLTAGE V RO Num ND NC PT FI
05.006 Motor Rated Frequency 0.00 to 550.00 Hz
50Hz: 50.00 Hz
60Hz: 60.00 Hz
RW Num US
05.007 Motor Rated Current ±VM_RATED_CURRENT A 0.00 A RW Num RA US
05.008 Motor Rated Speed 0.0 to 33000.0 rpm
50Hz: 1500.0 rpm
60Hz: 1800.0 rpm
RW Num US
05.009 Motor Rated Voltage ±VM_AC_VOLTAGE_SET V
110V drive: 230 V
200V drive: 230 V
400V drive 50Hz: 400 V
400V drive 60Hz: 460 V
575V drive: 575 V
690V drive: 690 V
RW Num RA US
05.010 Motor Rated Power Factor 0.00 to 1.00 0.85 RW Num RA US
05.011 Number Of Motor Poles 0 to 16 Pole pairs 0 Pole pairs RW Num US
05.012 Auto‑tune 0 to 2 0 RW Num NC
05.013 Dynamic V To F Select 0 to 1 0 RW Num US
05.014 Open‑loop Voltage Mode
Ur.S (0), Ur (1), FD (2), Ur.Auto (3), Ur.I (4),
SrE (5), Fd.tap (6)
Ur.I (4) RW Txt US
05.015 Low Frequency Voltage Boost 0.0 to 25.0 % 3.0 % RW Num US
05.017 Stator Resistance 0.0000 to 99.9999 Ω 0.0000 Ω RW Num RA US
05.018 Maximum Switching Frequency 0 to VM_MAX_SWITCHING_FREQUENCY kHz 3 (3) kHz RW Txt RA US
05.019 High Stability Space Vector Modulation Off (0) or On (1) Off (0) RW Bit US
05.020 Over Modulation Enable Off (0) or On (1) Off (0) RW Bit US
05.024 Transient Inductance 0.000 to 500.000 mH 0.000 mH RW Num RA US
05.025 Stator Inductance 0.00 to 5000.00 mH 0.00 mH RW Num RA US
05.027 Slip Compensation Level ±150.0 % 100.0 % RW Num US
05.028 Flux Control Compensation Disable Off (0) or On (1) Off (0) RW Bit US
05.031 Voltage Controller Gain 1 to 30 1 RW Num US
05.032 Torque Per Amp 0.00 to 500.00 Nm/A RO Num ND NC PT
05.033 Slip Compensation Limit 0.00 to 10.00 Hz 10.00 Hz RW Num US
05.035 Auto‑switching Frequency Change Disable 0 to 1 0 RW Num US
05.036 Slip Compensation Filter 64 (0), 128 (1), 256 (2), 512 (3) ms 128 (1) ms RW Txt US
05.037 Switching Frequency 0 to VM_MAX_SWITCHING_FREQUENCY kHz RO Txt ND NC PT
05.038 Minimum Switching Frequency 0 to VM_MAX_SWITCHING_FREQUENCY kHz 0.667 (0) kHz RW Txt RA US
05.040 Spin Start Boost 0.0 to 10.0 1.0 RW Num US
05.042 Reverse Output Phase Sequence Off (0) or On (1) Off (0) RW Bit US
05.059 Maximum Deadtime Compensation 0.000 to 10.000 µs 0.000 µs RO Num NC PT US
05.060 Current At Maximum Deadtime Compensation 0.00 to 100.00 % 0.00 % RO Num NC PT US
05.061 Disable Deadtime Compensation Off (0) or On (1) Off (0) RW Bit US
05.074 Boost End Voltage 0.0 to 100.0 % 50.0 % RW Num US
05.075 Boost End Frequency 0.0 to 100.0 % 50.0 % RW Num US
05.076 Second Point Voltage 0.0 to 100.0 % 55.0 % RW Num US
05.077 Second Point Frequency 0.0 to 100.0 % 55.0 % RW Num US
05.078 Third point voltage 0.0 to 100.0 % 75.0 % RW Num US
05.079 Third point frequency 0.0 to 100.0 % 75.0 % RW Num US
05.080 Low acoustic noise enable Off (0) or On (1) Off (0) RW Bit US
05.081 Change to maximum drive switching frequency at low output current Off (0) or On (1) Off (0) RW Bit US
05.083 Voltage Shelving Disable Off (0) or On (1) Off (0) RW Bit US
05.084 Low Frequency Torque adjustment 0.0 to 100.0 % 0.0 % RW Num US
05.088 Ur Mode Pre‑Flux delay 0.0 to 0.7 s 0.1 s RW Num US
RW Read / Write RO Read-only Bit Bit parameter Txt Text string Date Date parameter Time Time parameter
Chr Character parameter Bin Binary parameter IP IP address Mac MAC address Ver Version number SMP Slot, menu, parameter
Num Number parameter DE Destination ND No default value RA Rating dependent NC Non-copyable PT Protected
FI Filtered US User save PS Power-down save
To Next Page
Loading...
