Hurco winmax - Page 296

XVIII - Index v546CO WinMax Lathe Conversational Part Programming
RAPID field
Axial Mill Flats screen 2 - 169
Axial Mill Slot screen 2 - 161
Radial Slot screen 2-104
RAPID TO POSITION field 2-7
Rapid to W Position? field
Transfer block screen 2 - 209
RAPID TRAVERSE field
Change Parameters 2-193
READ TABLE FROM FILE F4 softkey
Part Setup Work Offsets 2 - 197
Reaming operation 2-120
rectangular coordinates 2-133, 2 - 151,
2-158, 2 - 162, 2 - 171, 2-182, 2-
185
reference corner, radial mill frame 2-100,
2-102, 2 - 109, 2-158
REFERENCE field
part zero or machine zero 2-4, 2-8
User Defined Tool Change Position area
in Program Parameters screen
2 - 194
REPEAT COUNT field 2-202
Repeat End description 1-5
REPEAT END F2 softkey 2-203
REPEAT END F7 softkey 2-203
Repeat End screen 2 - 203
Repeat Start description 1-5
REPEAT START F6 softkey 2-202
Repeat Start screen 2 - 202
RETRACT ALONG PROFILE field
Roughing 2-16
RETRACT ANGLE field
Grooving 2-53
Profile Start screen 2-16, 2-19, 2-
20, 2-22
RETRACT AT RAPID field
Axial Holes Drill Operation screen 2-
182
Cutoff block 2-64
Radial Holes Drill Operation screen 2-
120
RETRACT CLEARANCE field
Grooving 2-53
Profile Start screen 2-16, 2-19, 2-
21, 2-23
RETRACT DISTANCE field
Cutoff block 2-64
RETRACT FEED field
Cutoff block 2-64
RETRACT LEVEL field
Holes cycle 2-61
RETURN field
Axial Bolt Circle screen
Polar Coordinates 2 - 185
Axial Locations screen
Polar Coordinates 2 - 183
Rectangular Coordinates 2-184
Radial Holes Locations screen
Rotary Coordinates 2 - 122
RETURN LEVEL field
Axial Bolt Circle screen
Rectangular Coordinates 2-186
Radial Holes Locations screen
Linear Coordinates 2-122
Radial Holes Loop Around C-Axis screen
2-123
review 1-8
RIGHT field
Axial Mill Contour screen 2 - 129
Cutter Compensation 2-189
Radial Mill Contour screen 2-72
RIGID field
Axial Holes Drill Operation screen 2-
181
Radial Holes Drill Operation screen 2-
119
rigid tap 2-60
rotary coordinates 2-76, 2-93, 2-100,
2-105, 2 - 121
ROUGH AND FINISH field
Axial Mill Circle screen 2-147
Axial Mill Contour screen 2 - 128
Axial Mill Flats screen 2 - 168
Axial Mill Frame screen 2-154
Axial Mill Slot screen 2 - 161
Groove screen 2-53
Radial Mill Circle screen 2-90
Radial Mill Contour screen 2-71
Radial Mill Frame screen 2-96
Radial Slot screen 2-103
ROUGH FINAL DEPTH field
Threading 2-39
ROUGH ONLY field
Axial Mill Circle screen 2-147
Axial Mill Contour screen 2 - 128
Axial Mill Flats screen 2 - 168
Axial Mill Frame screen 2-154
Axial Mill Slot screen 2 - 161
Groove screen 2-53
Radial Mill Circle screen 2-90, 2-96
Radial Mill Contour screen 2-71
Radial Slot screen 2-103
ROUGH START DEPTH field
Threading 2-39
RPM field
Transfer block screen 2 - 208