Need help?Do you have a question about the Kentrox RMX-3200 and is the answer not in the manual?
General| Brand | Kentrox |
|---|---|
| Model | RMX-3200 |
| Category | Network Hardware |
| Language | English |
Details the connectors and counts of the Remote RMX-3200 base unit and its expansion capabilities.
Step-by-step guide to connecting and logging into the RMX-3200 via the console port using Kentrox Kickstart or other terminal software.
Guides through initial configuration steps including user setup, banner, hostname, IP address, and remote access protocols.
Instructions for connecting to the RMX-3200 CLI remotely using Telnet or SSH connections.
Details on how to access and navigate the RMX-3200 web interface for device management.
Step-by-step instructions for adding a new user account with specific profiles and passwords.
Instructions on how to save the current running configuration to the startup configuration via CLI and Web interface.
Guides on setting the domain name, primary/secondary DNS servers, and enabling IP forwarding.
Steps to configure an IPv6 address for the interface bridge switch.
Procedure for configuring primary/secondary NTP servers, polling intervals, and enabling NTP.
Details on configuring timezones, daylight savings, and local time/date settings.
Guides on configuring RAS server type, address, accounting, authorization, retry, and timeout settings.
Instructions for configuring SNMP version 1/3 community strings, management stations, and traps.
Guides on setting T1/E1 line buildout, framing format, bit-level encoding, and loopback detection.
Steps to configure controller speed, DS0 channels, and enable channel groups for T1/E1 links.
Details on configuring PPP encapsulation, default routes, authentication methods, MRU/MTU, and inactivity timeouts.
Procedure for configuring T1/E1 serial interface with channel groups, descriptions, and IP addresses.
Guides on configuring PPPoE encapsulation for Ethernet controllers, including default routes and authentication.
Steps to configure port VLAN mode and assign VLAN identifiers for Ethernet controllers.
Steps to configure the site LAN interface, including removing controllers and setting IP forwarding.
Guides on configuring the site VPN controller, interface, client routes, and access permissions.
Procedure to verify client connectivity and the number of connected clients to the site VPN.
Steps to configure Ethernet, asynchronous serial, and T1/E1 controllers as part of the bridge group.
Guides on configuring STP parameters like forward delay, hello time, maximum age, and priority level.
Procedure to add an IPv4 static route with destination, subnet mask, and gateway address.
Steps to add a default IPv4 static route with a specified gateway address.
Procedure to add an IPv6 static route with destination, subnet mask, and gateway address.
Steps to add a default IPv6 static route with a specified gateway address.
Guides on configuring UMTS/EvDO wireless modem settings, including description, connection string, and PPP encapsulation.
Steps to configure OpenVPN controller, encryption, server IP address, and interface for VPN setup.
Describes the elements of event declarations: event name, originator, and type.
Details the elements of response declarations: response name, responder, and response type.
Explains the elements of action declarations: action name, event name, and response name.
Step-by-step guide to configuring an event, response, and action for system automation.
Guides on configuring the DHCP server to assign IP addresses to technician laptops.
Steps to configure IPTables rules for Network Address Translation (NAT) for private network access.
Details components of correlation expressions, including terms, operators, and originator types.
Step-by-step process for configuring event correlations, including expressions, durations, and alarm entries.
Guides on configuring alarm entries for temperature sensor readings, including events and SNMP traps.
Steps to configure alarm entries for discrete inputs, including TL1 support and events.
Procedure to configure alarm entries for MAC security violations on Ethernet interfaces.
Guides on configuring alarm entries for serial connection failures, including SNMP trap support.
Steps to configure alarm entries for power supply failures, including TL1 support and events.
To Next Page
