Lexmark MX71X - Page 119

Error code Description Action
242.19 HCIT: Failed to feed from tray 2—the leading
edge of the media was not detected.
Go to
“HCIT jam service check” on page 132.
242.20 250/550‑sheet tray: Took too long to ramp up
media feeder motor in tray 2
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.20 HCIT: Took too long to ramp up media feeder
motor in tray 2
Go to
“HCIT jam service check” on page 132.
242.21 250/550‑sheet tray: Media feeder motor stall
in tray 2.
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.21 HCIT: Media feeder motor stall in tray 2. Go to
“HCIT jam service check” on page 132.
242.22 250/550‑sheet tray: Media feeder motor pick
motor under‑speed in tray 2.
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.22 HCIT: Media feeder motor pick motor
under‑speed in tray 2.
Go to
“HCIT jam service check” on page 132.
242.24 250/550‑sheet tray: Media feeder motor
stalled on the last pick attempt in tray 2.
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.24 HCIT: Media feeder motor stalled on the last
pick attempt in tray 2.
Go to
“HCIT jam service check” on page 132.
242.29 Media feeder motor did not turn off when
lifting the tray
Go to
“Media feeder motor tray lift error service check” on
page 115.
242.32 250/550‑sheet tray: Tray 2 not ready Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.32 HCIT: Tray 2 not ready Go to
“HCIT jam service check” on page 132.
242.33 250/550‑sheet tray: The media tray was
pulled during the media pick process.
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.33 HCIT: The media tray was pulled during the
media pick process.
Go to
“HCIT jam service check” on page 132.
242.41 250/550‑sheet tray: Media feeder motor stall
in tray 2
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.41 HCIT: Media feeder motor stall in tray 2 Go to
“HCIT jam service check” on page 132.
242.42 250/550‑sheet tray: Media feeder motor
under‑speed in tray 2
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.42 HCIT: Media feeder motor under‑speed in
tray 2
Go to
“HCIT jam service check” on page 132.
242.43 250/550‑sheet tray: Media feeder motor did
not reach the required speed
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.43 HCIT: Media feeder motor did not reach the
required speed
Go to
“HCIT jam service check” on page 132.
242.44 250/550‑sheet tray: Separator pass through
motor stall in tray 2
Go to
“250/550-sheet media tray option jam service check” on
page 129.
242.44 HCIT: Separator pass through motor stall in
tray 2
Go to
“HCIT jam service check” on page 132.
7463
Diagnostic information
119