Mazda 6 2002 - Page 606

ON-BOARD DIAGNOSTIC (ABS/TCS)
P49
P
ABSLR_O
(Left rear ABS pressure
reduction solenoid valve
output state)
ON/OFF
• During ABS or EBD
control: ON/OFF
(solenoid valve is
activated/deactivated)
• Not ABS and EBD control:
OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSRF_O
(Right front ABS pressure
reduction solenoid valve
output state)
ON/OFF
• During ABS control: ON/
OFF
(solenoid valve is
activated/deactivated)
• Not ABS control: OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSLF_O
(Left front ABS pressure
reduction solenoid valve
output state)
ON/OFF
• During ABS control: ON/
OFF
(solenoid valve is
activated/deactivated)
• Not ABS control: OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSRR_I
(Right rear ABS pressure
reduction solenoid valve
output state)
ON/OFF
• During ABS control: ON/
OFF
(solenoid valve is
activated/deactivated)
• Not ABS control: OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSLR_I
(Left rear ABS pressure
retention solenoid valve
output state)
ON/OFF
• During ABS or EBD
control: ON/OFF
(solenoid valve is
activated/deactivated)
• Not ABS and EBD control:
OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSRF_I
(Right front ABS pressure
retention solenoid valve
output state)
ON/OFF
• During ABS control: ON/
OFF
(solenoid valve is
activated/deactivated)
• Not ABS control: OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSLF_I
(Left front ABS pressure
retention solenoid valve
output state)
ON/OFF
• During ABS control: ON/
OFF
(solenoid valve is
activated/deactivated)
• Not ABS control: OFF
(solenoid valve is
deactivated)
Internal fault of ABS (ABS/
TCS) HU/CM. Replace ABS
(ABS/TCS) HU/CM.
(See P28 ABS (ABS/TCS)
HU/CM REMOVAL/
INSTALLATION)

ABSVLVRLY
(Fail-safe relay output
state)
ON/OFF
• Fail-safe relay is
activated: ON
• Fail-safe relay is
deactivated: OFF
Inspect ABS (ABS/TCS)
HU/CM.
(See P29 ABS (ABS/TCS)
HU/CM INSPECTION )

ABSPMPRLY
(Motor relay output state)
ON/OFF
• Motor relay is activated:
ON
• Motor relay is deactivated:
OFF
Inspect ABS (ABS/TCS)
HU/CM.
(See P29 ABS (ABS/TCS)
HU/CM INSPECTION )

LF_WSPD
(Left front wheel-speed
sensor input)
KPH or MPH
• Vehicle is stopped: 0 KPH
{0 MPH}
• Vehicle is driving:
Indicates vehicle speed
Inspect wheel-speed
sensor/sensor rotor.
E, I
PID Name
(Definition)
Unit/Condition Condition/Specification Action
ABS (ABS/
TCS) HU/CM/
CM terminal