Omron ZW-7000 Series - Page 195

Search from Menu Tree
ZW-7000/5000
User's Manual
193
Sensor controller operations
7
Setting Option/Setting Range Pages
I/O setting
[I/O]
Digital output
[DIGTAL]
Clamp value
[CLAMP]
0x7FFFFFFF[MAX] /
999999999[99999] / 0 [0] /
-999999999 [-99999] /
0x80000000[MIN]*
*1
(cont'd) (cont'd)
Analog output
[ANALOG
Output
de
sti
nation
*1
[V OR C]
Output
destinat
ion
[V OR C]
Voltage output
*1
/Current output
*2
Output target
[OUTPUT]
Output target
[OUTPUT]
Off [OFF]/TASK1 [TASK1]
*1
/
TASK2 [TASK2]/TASK3 [TASK3]/
TASK4 [TASK4]
*2
Monitor focus
[FOCUS]
Focus
[FOCUS]
Off [OFF]
*1
/On [ON]
*2
Focus
current/
voltage 1
[CUR1]/
[V
OL
T1]
Current: 4/5/6/7/8/9/10/11/12/13/14/15/
16/17/18/19/20mA (default value: 4mA)
Current: -10/-9/-8/-7/-6/-5/-4/-3/-2/-1/
0/1/2/3/4/5/6/7/8/9/10V
(default value: -10V)
Measurement
value 1
[MEAS1]
-999.999999 to 999.999999 mm
(default value: -0.5)
Focus
current/
v
oltage 2
[CUR2]/
[V
OL
T2]
Current: 4/5/6/7/8/9/10/11/12/13/14/15/
16/17/18/19/20mA (default value: 20mA)
Current: -10/-9/-8/-7/-6/-5/-4/-3/-2/-1/
0/1/2/3/4/5/6/7/8/9/10V
(default value: 10V)
Measurement
data2
[MEAS2]
-999.999999 to 999.999999 mm
(default value: 0.5)
Calibration
[CALIB]
Calibration
[CALIB]
Off
*1
/On
*2
Calibration
current/
voltage 1
[CUR1]/
[V
OL
T1]
Current: 4/5/6/7/8/9/10/11/12/13/14/15/
16/17/18/19/20mA (default value: 4mA)
Current: -10/-9/-8/-7/-6/-5/-4/-3/-2/-1/
0/1/2/3/4/5/6/7/8/9/10V
(default value: -10V)
Calibration
v
alue 1
[A
DJ1]
-999 to 999 (default value: 0)
Calibration
current/
v
oltage 2
[CUR2]/
[V
OL
T2]
Current: 4/5/6/7/8/9/10/11/12/13/14/15/
16/17/18/19/20mA (default value: 20mA)
Current: -10/-9/-8/-7/-6/-5/-4/-3/-2/-1/
0/1/2/3/4/5/6/7/8/9/10V
(default value: 10V)
Calibration
v
alue 2
[A
DJ2]
-999 to 999 (default value: 0)
Clamp value:
[CLAMP]
Clamp
valu
e:
[CLAMP]
Current output: MIN[MIN] (approx.
3.4mA)
/4mA/5mA/.../19mA/20mA/
MAX[MAX] (approx, 20.8mA) (default
value: MAX)
Current output: MIN[MIN] (approx.
-10.8V)/-10V/-9V/.../9V/10V/
MA
X[MA
X
] (approx.10.8V)
(default value: MAX)
*2
*1. The same “OUTPUT” is set for all banks. The output destination cannot be set separately for individual banks.
*2. For more detail, refer to the following.
2-1 Connecting Parallel I/O in Confocal Fiber Type Displacement Sensor User's Manual for Communications Settings
(Cat. No.Z363).