Rohde & Schwarz R&S SMB100B - Page 508

Remote control commands
R&S
®
SMB100B
508User Manual 1178.3711.02 ─ 08
// Activate RF Output1.
Output1:STATe 1
// Execute combined frequency / level sweep
SOURce1:SWEep:COMBined:EXECute
[:SOURce<hw>]:SWEep:POWer:DWELl...........................................................................508
[:SOURce<hw>]:SWEep:POWer:MODE...........................................................................509
[:SOURce<hw>]:SWEep:POWer:POINts.......................................................................... 509
[:SOURce<hw>]:SWEep:POWer:SPACing:MODE?........................................................... 509
[:SOURce<hw>]:SWEep:POWer:STEP[:LOGarithmic]....................................................... 510
[:SOURce<hw>]:SWEep[:FREQuency]:DWELl..................................................................510
[:SOURce<hw>]:SWEep[:FREQuency]:MODE..................................................................510
[:SOURce<hw>]:SWEep[:FREQuency]:POINts..................................................................511
[:SOURce<hw>]:SWEep[:FREQuency]:SPACing............................................................... 511
[:SOURce<hw>]:SWEep:POWer:SHAPe..........................................................................512
[:SOURce<hw>]:SWEep[:FREQuency]:SHAPe................................................................. 512
[:SOURce<hw>]:SWEep:POWer:EXECute....................................................................... 512
[:SOURce<hw>]:SWEep[:FREQuency]:EXECute.............................................................. 512
[:SOURce<hw>]:SWEep:POWer:RETRace.......................................................................512
[:SOURce<hw>]:SWEep[:FREQuency]:RETRace..............................................................512
[:SOURce<hw>]:SWEep:POWer:RUNNing?..................................................................... 513
[:SOURce<hw>]:SWEep[:FREQuency]:RUNNing?............................................................ 513
[:SOURce<hw>]:SWEep[:FREQuency]:STEP:LOGarithmic................................................ 513
[:SOURce<hw>]:SWEep[:FREQuency]:STEP[:LINear].......................................................513
[:SOURce<hw>]:COMBined:FREQuency:STARt............................................................... 513
[:SOURce<hw>]:COMBined:FREQuency:STOP................................................................514
[:SOURce<hw>]:COMBined:POWer:STARt...................................................................... 514
[:SOURce<hw>]:COMBined:POWer:STOP.......................................................................514
[:SOURce<hw>]:SWEep:COMBined:COUNt.....................................................................515
[:SOURce<hw>]:SWEep:COMBined:DWELl..................................................................... 515
[:SOURce<hw>]:SWEep:COMBined:EXECute..................................................................515
[:SOURce<hw>]:SWEep:COMBined:MODE......................................................................516
[:SOURce<hw>]:SWEep:COMBined:RETRace................................................................. 516
[:SOURce<hw>]:SWEep:COMBined:SHAPe.....................................................................516
[:SOURce<hw>]:SWEep:RESet[:ALL].............................................................................. 517
[:SOURce<hw>]:SWEep:POWer:DWELl <Dwell>
Sets the dwell time for a level sweep step.
Parameters:
<Dwell> float
Range: 0.001 to 100
Increment: 100E-6
*RST: 0.01
Example: See Example"Setup an RF frequency or power sweep"
on page 506.
Manual operation: See "Dwell Time" on page 133
SOURce subsystem