YASKAWA AC Drive-A1000 - Page 527

P Control ......................................................................... 141
Peak Hold Current .............................................................. 452
Peak Hold Output Frequency ................................................. 452
Performance Life ............................................................ 351, 3
Performance Life Monitors Maintenance Monitors........................... 3
Periodic Inspection ............................................................. 349
Periodic Maintenance .......................................................... 225
Permanent Magnet Motor Control............................................... 3
PF ................................................................................. 312
PG 1 Division Rate for PG Pulse Monitor .................................. 197
PG 1 Gear Teeth 1 .............................................................. 198
PG 1 Gear Teeth 2 .............................................................. 198
PG 1 Pulses Per Revolution ................................................... 196
PG 1 Rotation Selection ....................................................... 197
PG 1 Signal Selection .......................................................... 198
PG 2 Division Rate for PG Pulse Monitor .................................. 197
PG 2 Gear Teeth 1 .............................................................. 198
PG 2 Gear Teeth 2 .............................................................. 198
PG 2 Pulses Per Revolution ................................................... 196
PG 2 Rotation Selection ....................................................... 197
PG 2 Signal Selection .......................................................... 198
PG-B3 ............................................................................ 361
PG-B3 Settings.................................................................. 196
PG Disconnect (for any control modes using a PG option card) ......... 312
PG Disconnect (for Control Mode with PG)................................ 322
PG Hardware Fault (detected when using a PG-X3 option card) ...312,
322
PG Number of Pulses Per Revolution........................................ 107
PG Number of Pulses Per Revolution for PM Motor Tuning............. 110
PGo ......................................................................... 312, 322
PGoH ....................................................................... 312, 322
PG Open-Circuit Detection Time............................................. 196
PG Option Card Disconnection Detection 1 ................................ 198
PG Option Card Disconnection Detection 2 ................................ 198
PG Option Card Port for Motor 2 Selection................................. 199
PG Speed Control Card Settings.............................................. 196
PG-X3 ............................................................................ 361
PG-X3 Settings.................................................................. 196
Phase Order Selection.......................................................... 132
PID Accel/Decel Time ......................................................... 148
PID Block Diagram............................................................. 143
PID Control...................................................................... 141
PID Feedback ................................................................... 453
PID Feedback High Detection Level......................................... 147
PID Feedback High Detection Time ......................................... 147
PID Feedback Input Methods ................................................. 142
PID Feedback Loss ....................................................... 305, 319
PID Feedback Loss Detection Selection..................................... 146
PID Feedback Low Detection Level ......................................... 146
PID Feedback Low Detection Time.......................................... 147
PID Fine Tuning ................................................................ 149
PID Function Setting ........................................................... 144
PID Input (feedback) ........................................................... 453
PID Input Limit ................................................................. 149
PID Monitors .................................................................... 284
PID Offset Adjustment......................................................... 145
PID Output....................................................................... 454
PID Output Fault................................................................ 342
PID Output Gain Setting....................................................... 145
PID Output Level Selection ................................................... 145
PID Output Limit
............................................................... 144
PID Output Lower Limit....................................................... 148
PID Output Reverse Selection ................................................ 145
PID Primary Delay Time Constant........................................... 145
PID Setpoint ..................................................................... 454
PID Setpoint Display Digits................................................... 149
PID Setpoint Input Methods................................................... 142
PID Setpoint Scaling ........................................................... 148
PID Setpoint Selection ......................................................... 148
PID Setpoint User Display .................................................... 149
PID Setpoint Value ............................................................. 148
PID Sleep ........................................................................ 147
PID Sleep Delay Time ......................................................... 147
PID Sleep Function Start Level............................................... 147
PM Inductance Error ........................................................... 331
PM Motor Auto-Tuning Mode Selection.................................... 108
PM Motor Base Frequency .................................................... 109
PM Motor Base Speed ......................................................... 109
PM Motor Code................................................................. 193
PM Motor Code Selection ..................................................... 108
PM Motor Control Tuning..................................................... 275
PM Motor d-Axis Inductance ................................................. 110
PM Motor Induced Voltage Constant........................................ 110
PM Motor Parameter Settings................................................. 101
PM Motor q-Axis Inductance ................................................. 110
PM Motor Rated Current ...................................................... 109
PM Motor Rated Power........................................................ 109
PM Motor Rated Voltage ...................................................... 109
PM Motor Settings ............................................................. 108
PM Motor Stator Resistance .................................................. 110
PM Motor Type ................................................................. 109
PM Stationary Auto-Tuning................................................... 101
PM Stationary Auto-Tuning for Stator Resistance ......................... 101
Pole Attraction Current ........................................................ 275
Power Detection Filter Time .................................................. 152
Powering Up the Drive...........................................................96
Power Ratings (Three-Phase 600 V Class).................................. 373
Predefined V/f Patterns ........................................................ 184
Preface..............................................................................16
Preparing the Ends of Shielded Cables ........................................66
Preset Reference Timing Diagram ........................................... 171
Previous Fault ................................................................... 450
PROFIBUS-DP Clear Mode Selection ...................................... 204
PROFIBUS-DP Data Format Selection...................................... 204
PROFIBUS-DP Node Address ............................................... 203
PROFIBUS-DP Parameters ............................................. 201, 203
Programming Mode ......................................................... 84, 85
Proportional Gain Setting (P) ................................................. 144
Protective Cover ..................................................................41
Protective Covers, Removing ...................................................55
Protective cover to prevent miswiring .........................................36
PTC ............................................................................... 233
Pull-In Current ............................................................ 276, 438
Pull-In Current Compensation Time Constant.............................. 438
Pull-In Current during Accel/Decel for PM................................. 314
Pull-In Current Level for PM Motor Tuning................................ 110
Pulse Monitor Selection Error ................................................ 327
Pulse Output Connection Using External Voltage Supply ..................70
Pulse Output Connection Using Internal Voltage Supply...................69
Pulse Train Input/Output....................................................... 217
Index
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
527